Downloaded from https://www.everyspec.com LJ STRUCTURES 4~ I L, eqaipi ant. The unprotected design should that minii.:v.s the thermal stresses caused " of course be compared with insuleted and by uneven distribution of material and vari- cooled designs in order tr arrive at an opii- ations in the heat transfer coefficient. For mum of r:;,fig4:ation. wing-like structures, trussed and corrugated Unprotected structures ha~e been classi- webs and ribr have been investigated. Con- fled - into three categories depending on the sideration has also been give, to sandwich manner N which the effects of aerodynamic construction of the surface to surfate and heating are handied:
(a) heat-sustainlng, individual surface types, and the z-e of shal- (b) beat sink, and (c) thermal stre.-s reduc- low, closely spaced s.ringers. In e-ch of the ing types. On the heat susaining type of configurations mentioned thb. basic idea is to structure t.e most complex problems arise avoid concentrations of material which give from the effects of th3rrmal expansion which rise to temperature differences, and hence cause structural growth, structural distor- thermal stresses, in a structural component. tion, and theri.ai stresses. Structural growth, The ::losely spaced shallow stringer config- for example, q:ves rise to detail design prob.
them down into a numIser of smaller heat lemni in the Ltachment of internal equipment sinks. The shallow depth keeps the average to the missile body and of surface control stringer temperature close to the skin tm- which compensates for growth of the struc. perature, thus reducing the thermal stresses. ture. Structural distortions are unavoidable Introducing a flexible connection or support in the unprotected type of strnture. Even between components avoids a build up of in- if equilibrim temperatures are attained, tem- teral stresses due to constraints. peratures are not uniform over the surface of the structure due to variations in heat 4-3.2.
Insulated Structures The insukto transfe" co-efficients and local concentrations structure introduces the conccpt of one struc- of material which serve as heat sinks. As ture to absorb the primary loads and a second structure to cope with the thermal input. ; mentioned in the early part of this chapter, Consider, for example, a cor---ntional struc- variations in temperature from an average temperature give rise to thermal stresses and tura configuration of a material which may attention must be given to the possibility of iais A fair oinsulatg mater stress concentrations or thermal bitckling.
be applied to the surface of the structure to In th e h -?at s in k a p p r o a ch , ex tr ,- n a t~ -' a l k e p t e e m r a u e o th l ad c ry n is added to the external surface of the mis- keep the temperature of the load carrying sile. Tbis addition of material has the effect posite type of structure, however, requires of reducing temperatures, increasing mate- eite reior stc h r re rf rial strength and reducing structural growth and distortions. The thermal stresses, how- the insulating material in order to compare solution to the aerodynamic heating problem Moreover, the insulatitig material has strin- soltio totheaerdynmicheaingprolem gent mechanical and thermal requirements.
is most efficient when adiabatic wall tmpera e tures and flight times are such that additional It should be erosion and beat resistant, and ever, di.sy not be changed significantly. This favorably with the double wall solution. material can be added to a light alloy struc- it must possess good adhesive character- ture. This is because specific heats of the istics. Although some ceramics and refrac- light alloys are considerably higher than the tories appear to have some of these esirable specific heats of alloys of steel and titanium.
properties, it seems that the necessary re- For very short exposure times, the mechani- quirements are too severe to be met by a cal properties of this configuration are far single material. Many refractory materials are brittle and have low thermal shock re- -superior to those shown in Chapter 2 for ssac.Atog eaisi h xd wh ich exposure times may be one-half hour sistance. Although ceramics in the oxide c eo ue family have a lower thermal conductivity or more. than those in the silicide, boride or carbide The stress redtcing type of structure A. an groups, a 0.10 inch coating of aluminum ( " Otempt to evolve a structural configuration oxide would have little insulating value in 60