US Army Materiel Command AMCP 706-341 — Engineering Design Handbook — Carriages and Mounts Series: Cradles

Downloaded from https://www.everyspec.com where b 3.96 in (see Figure 29, Paragraph therefore i 76). KR = K - (f + fI) = 149,200 - 0.30R - The pressure meets the conditions stated in MR. = 0 Paragraph 28. (c-e)KR + eF, - (e-d) (F. - W sin 0) 80. The critical compressive stress obtained - aW cos a - (e-h)ft - (a-b)R = 0 of the gussets buckling is extremely remote. (e-h)f = 1.0(0.15R) = 0.15& E K 540,000 lb 'in' (c-e)KR = 8(149,200- 0.30 RI) = K.1 = 1,194,000 - 2.40R 1 where a = 3.96 in K. = 1.06 eF, = 8 X 1,810,000 = 14,480,000 b = 3.45 in t = 0.5in (e-d)(F. - Wsin0) = 7.9 X 1,660,000 E = 29 x 10, lb /in - P =(6.3 = 13,114,000 aW cos0 = 80 X 5000 = 400,000 62.55Rt = 2,160,000 VIL.

SAMPLE PROBLEM, U-TYPE R, = 34,500 lb CRADLE R 2 = 39,500 lb A. LOAD ANALYSIS A = 5200 lb C 81. A U-type cradle is selected for 'the f2 = 5900 lb sample problem involving a single recoil gun KR = 138,900 lb carriage. Figure 5a represents the loading diagram for the analysis 1. Rails and Slides a = 80 in i = 0.1 in 83. The reactions Rt and R2 are carried b = 20 in e = 8 in equally by two rails, each 90 inches long. c = 16 in h = 7 in These reactions have an assumed triangular W, = 10,000 Ib, weight of recoiling parts distribution, but the reaction due to rifling F, = 1,810,000 lb, propellant gas force torque is distributed uniformly.

The rails are ( K = 150,000 lb, total recoil resistance 3.0 inches wide and their center-to-center = 0.15, coefficient of friction distance is 17 inches. From Paragraph 74, 0 = 60*, angle of elevation T, = 545,000 lb-in 82. The values of R 1 , R 2 , ft, f2 and KR are F, = d 1 32,000 lb unknown. These are found by balancing the d 7 loads and moments. F, 3 From Equation 3, since F, is zero, the inertia 90 force is Let R 2 represent the triangular portion of F. = F, + W, sine - K R2(see Figure 12).

= 1,810,000 + 8700 - 150,000 = 1,668,700 lb 1 w2 = R2 XV = 0 R, -R 2 +Wcos 0 = 39,500 = 8751b/in R 2 =R + 5000 45 H o w = w 2 + w, = 12301b/in From Equation 2 The maximum bearing pressure becomes K, + f + f 2 -K 0 : = 410 lb/in' but from Equations 1 and lU 3 h = uR, = 0.15R, This pressure is acceptable according to f2 = A2 = 0.15 (R + 5000) Paragraph 28. 34