Downloaded from https://www.everyspec.com AMCP 706.117 pollutants throughout the atmosphere. Airspeed and (2) Fabricm The primary means of sample evalua- atmospheric turbulence determine the r.sidence time of tion for textiles is to measure the loss in tensile strength. airborne particulate matter, the deposition site, i.e., This may be reported as percent breaking strength re- whether it impacts on vertical surfaces or settles as tained (Ref. 42). Also, for undyed samples the degree dustfall on horizontal surfaces, and, for solid particles, of soiling can be determined by reflectance measure- the extent of abrasion (Ref. 7). Periods of low wind- ments.
For materials such as knits, a test of tensile speeds are often associated with temperature inver- strength of a %ample does not subject fibers to straight- sions. In areas such as Los Angeles, high concentra- line tension; therefore, damage is usually measured tions of atmospheric pollutants build up because of the visually. In a study conducted to determine the damage lack of mixing or turbulent air currents in the inversion to nylon hose by sulfur dioxide and sulfur trioxide, the layer. Wind direction can be the most important varia- exposed stockings were stretched over inverted jars and ble, especially if the emissions are from one major microscopically examined for fiber breaks (Ref.
7). source. (3) DyZs Some dyed fabrics display a pronounced color change when exposed to polluted envitonments 2-7.3 METHODS OF MEASURING MATERIAL containing above-average concentrations of ozone, ni- DETERIORATION trogen oxides, or both. The color change is evaluated by means of specially designed colorimeters that detect In order to provide quantitative measures of matrial small changes of color within narrow ranges of the deterioration resulting from air pollutants, me~hods visible spectrum. have been developed for different classes of materials.
(4) Building materials It is generally agreed that These methods, described in the following subpara- sulfur dioxide does attack building stone but no care- graphs, are sometimes employed as an approximate fully planned exposure tests comparable to those for measure of the integrated pollutant concentration dur- metals have been conducted (Ref. 28). The usual ing the period of exposure. method of evaluating damage to stone and mortar by (1) MetalL Many methods have been used to evalu- atmospheric pollutants is to visually note the discolors- ate the results of corrosion tests.
They include appear- ton and loss of material due to leaching over a period ance ratings, weight losses, weight gains, pit depths, of years. Alio, the settling of particulate matter such as and losses in strength (Ref. 40). Most corrosion data soot on the walls of buildings can be evaluated visually are presented as weight gain or loss. In tests of short by comparing photographs of a building before and duration, a metal sample will gain weight due to the after cleaning. formation of corrosion products.
However, weight (5) Other materials The measurement of damage to gains are not completely satisfactory for quantitative lead-based paint from hydrogen sulfide is usually ac- purposes because some of the corrosion products may complished by observing the color change or darkening be separated from the specimen. In any case weight of the paint.
Quantitative data are usually derived from gains should be supplemented with an analysis of the exouecabrtsssigimledpltda- corrsionprodcts.exposure chamber tests using simulated polluted at- corrosion productsu mospheres because hydrogen sulfide tends to produce Weilht-loss measurements are usually preferred for a mottled effect in actual outdoor exposures making it test periods of long duration. For this measurement a diffcult to evaluate the color change of the paint (Ref. clean, weighed sample is exposed for a period of time, 7). The weakening of leather and embrittlement of pa- then cleaned and reweighed.
The loss in weight repre- per caused by sulfur dioxide have been observed but sents the corrosion that has occurred. The usual units have not been quantitatively measured. are milligrams of weight loss per square decimeter of surface per day or for the period of the test (mg/dm 2 /day). Some data obtained as weight loss are 2-7.4 MATERIALS DAMAGE convented to and reported as loss of metal thickness in 2-7.4.1 Ferrous Metals mils per year. Bending, tension, fatigue, impact, and electrical resistance messnrements are also used in spe- The electrochemical theory of corrosion is used to cial purpose tests.
For example, the electrical resistance explain the initiation of atmospheric corrosion on fer- across a set of points is used ass mesanure of the damage rous surfaces (Ref. 43). However, once the first rust has caused by air pollutants to electrical contact materials formed, the mechanisms and rates of further corrosion (Ref. 41). become very complex. For example, when iron remains 2.56 SEEN-