Chapter 2 Devices 2_ 2-17 Latched Attribute Default OFF STOP RUN SM Function ON RUN STOP SM475 Auto-reset for Y1 output is complete. OFF OFF – N R/W OFF *SM476 Output immediately stops when the instruction is disabled or stops for Y0/axis 1 (Y0/Y1) OFF OFF – N R/W OFF *SM477 Output immediately stops when the instruction is disabled or stops for Y1 OFF OFF – N R/W OFF SM478 Change the target positon while outputting Y0/axis 1 (Y0/Y1) OFF OFF – N R/W OFF SM479 Change the target positon while outputting Y1 OFF OFF – N R/W OFF SM480 Outputting Y2/axis 2 (Y2/Y3). OFF OFF – N R OFF SM481 Y2/axis 2 (Y2/Y3) output is complete.
OFF OFF – N R/W OFF SM482 Reversing the output direction of axis 2 (Y3) OFF OFF – N R/W OFF *SM483 Stopping the output of Y2/axis 2 (Y2/Y3) OFF OFF – N R/W OFF SM484 Enabling the positive maximum value for axis 2 (Y2/Y3). – – – Y R/W OFF SM485 Alarm: positive limit for axis 2 (Y2/Y3). OFF OFF – N R/W OFF SM486 Enabling the negative maximum value for axis 2 (Y2/Y3) . – – – Y R/W OFF SM487 Alarm: negative limit for axis 2 (Y2/Y3). OFF OFF – N R/W OFF *SM488 Enabling the S curve ramp-up/down for axis 2 (Y2/Y3). OFF OFF – N R/W OFF SM489 Enabling fixed slope ramp-up/down for axis 2 (Y2/Y3). OFF OFF – N R/W OFF SM490 Auto-reset for Y2/axis 2 (Y2/Y3) output is complete.
OFF OFF – N R/W OFF SM491 Executing an interrupt I501 when pulse output ends for axis 2 (Y2/Y3). OFF OFF – N R/W OFF SM492 Outputting Y3. OFF OFF – N R OFF SM493 Y3 output is complete. OFF OFF – N R/W OFF *SM494 Stopping the output of Y3. OFF OFF – N R/W OFF SM495 Auto-reset for Y3 output is complete. OFF OFF – N R/W OFF *SM496 The output immediately stops when the instruction is disabled or stops for Y2/axis 2 (Y2/Y3). OFF OFF – N R/W OFF *SM497 The output immediately stops when the instruction is disabled or stops for Y3.
OFF OFF – N R/W OFF SM498 Change the target positon while outputting Y2/axis 2 (Y2/Y3) OFF OFF – N R/W OFF SM499 Change the target positon while outputting Y3 OFF OFF – N R/W OFF SM500 Outputting Y4/axis 3 (Y4/Y5). OFF OFF – N R OFF SM501 Y4/axis 3 (Y4/Y5) output is complete. OFF OFF – N R/W OFF SM502 Reversing the output direction of axis 3 (Y5). OFF OFF – N R/W OFF *SM503 Stopping the output of Y4/axis 3 (Y4/Y5). OFF OFF – N R/W OFF SM504 Enabling the positive maximum value for axis 3 (Y4/Y5). – – – Y R/W OFF SM505 Alarm: positive limit for axis 3 (Y4/Y5) OFF OFF – N R/W OFF SM506 Enabling the negative maximum value for axis 3 (Y4/Y5) – – – Y R/W OFF SM507 Alarm:
negative limit for axis 3 (Y4/Y5) OFF OFF – N R/W OFF *SM508 Enabling the S curve ramp-up/down for axis 3 (Y4/Y5) OFF OFF – N R/W OFF SM509 Enabling fixed slope ramp-up/down for axis 3 (Y4/Y5) OFF OFF – N R/W OFF