electrolux WM-WD — Electrolux WM-WD — руководство по ремонту (EN)

E11 Difficulties in water fill for washing E12 Difficulties in water fill for drying E13 Water leakage faulty. E21 Difficulties in draining for washing E22 Difficulties in draining for drying E23 Drain pump triac faulty E24 Fault in “sensing” circuit of drain pump triac (wrong input signal to microprocessor) PCB faulty. E31 Electronic pressure switch circuit faulty (frequency of pressure switch signal out of limits) E38 Pressure chamber blocked (water level does not vary for at least 30 sec. during drum rotation or 5V) PCB faulty.

E41 Door open (after 15 sec.) E42 Problems of door closure E43 Interlock power supply triac faulty QUICK GUIDE AND APPLIANCES LIST Alarm Possible fault ENV06 EWM11xx EWM21xx EWM25xx/35xx pump faulty; E35 Water overflow E00 3.5 Table of alarms codes ENV06 Incorrect calibration of electronic pressure switch (The electronic pressure switch generates a signal with instable frequency during the drain phase) E3A Heating elem.

relay sensing faulty (input signal to microprocessor always 0V E32 Alarm Possible fault Action/machine status Reset Alarm E00 No alarm E11 Difficulties in water fill for washing Tap closed or water pressure too low; Drain tube improperly positioned; Water fill solenoid valve is faulty; Leaks from water circuit on pressure switch; Pressure switch faulty; Wiring faulty; PCB faulty. Cycle is paused with door locked. START/RESET E12 Difficulties in water fill for drying Tap closed or water pressure too low; Drain tube improperly positioned; Water fill solenoid valve is faulty; Leaks from water circuit on pressure switch; Pressure switch faulty; Wiring faulty; PCB faulty.

Cycle is paused with door locked. START/RESET E13 Water leakage Drain hose incorrectly positioned; mains pressure insufficient; water fill solenoid faulty; leakage/blockage of pressure switch hydraulic circuit; pressure switch faulty. Cycle is paused with door locked. START/RESET E21 Difficulties in draining for washing Drain tube kinked/clogged/improperly positioned; Drain filter clogged/dirty; Drain pump faulty; Pressure switch faulty; Wiring faulty; PCB faulty. Cycle is paused (after 2 attempts).

START/RESET E22 Difficulties in draining for drying Drain tube kinked/clogged/improperly positioned; Drain filter clogged/dirty; Drain pump faulty; Pressure switch faulty; Wiring faulty; PCB faulty. Cycle is paused. START/RESET E23 Drain pump triac faulty Drain pump faulty; Wiring faulty; PCB faulty. Safety drain cycle - Cycle stops with door unlocked. RESET E24 Fault in “sensing” circuit of drain pump triac (wrong input signal to microprocessor) PCB faulty. Safety drain cycle - Cycle stops with door unlocked. RESET E31 Electronic pressure switch circuit faulty (frequency of pressure switch signal out of limits) Electronic pressure switch; Wiring; PCB faulty. Cycle blocked with door closed.

RESET E32 Incorrect calibration of electronic pressure switch (The electronic pressure switch generates a signal with instable frequency during the drain phase) Drain tube kinked/clogged/improperly positioned; Drain filter clogged/dirty; Drain pump faulty; Leaks from water circuit on pressure switch; Pressure switch; Wiring faulty; PCB faulty. Cycle is paused. START/RESET E35 Water overflow Water fill solenoid faulty; Leaks from water circuit on pressure switch; pressure switch faulty; wiring faulty; PCB faulty. Cycle blocked. Safety drain cycle. Drain pump always in operation (5 minutes on, 5 minutes off etc.).

RESET E38 Pressure chamber blocked (water level does not vary for at least 30 sec. during drum rotation Motor drive belt broken; Hydraulic circuit pressure switch clogged. Heating phase skipped. ON/OFF RESET E3A Heating elem. relay sensing faulty (input signal to microprocessor always 0V or 5V) PCB faulty. Cycle blocked with door closed. RESET E41 Door open (after 15 sec.) Door interlock faulty; wiring faulty; PCB faulty. Cycle paused. START/RESET E42 Problems of door closure Door interlock faulty; wiring faulty; PCB faulty. Cycle paused. START/RESET E43 Interlock power supply triac faulty Door interlock faulty; wiring faulty; PCB faulty. (Safety drain cycle) Cycle blocked. ON/OFF RESET