US Army Materiel Command AMCP 706-197 — AMCP 706-197 Reliability Prediction Handbook — US Army Engineering Design Guide PDF

Downloaded from https://www.everyspec.com -U ?WS197 integral exists. In this concept, once the sys- handle a matrix, the analyst must subdivide tern fails, it is dead and cannot be repaired, the system into two or more separate sections with the MTBF (mean time between failures). The system s-reliability with repair is the It is important not to confuse the MTF and ompute s-reliability with repair fore MTBF may not be a workable concept for a product of the section s-rehiabilities; the MTF particular system ar : may not be readily is computed by numerically integrating the computed for complex repairable systems. system s-reliability. For piece parts which are discarded after fail- 14.

A k-out-of-n:G-system has n compo- ure or for items that are restored to their orig- nents and is Good (up) if and only if at least k inal conditions and used as new spares, MTF of them are Good (up). is the appropriate concept. 15. A k-out-of-n:F-system has n compo- 6. Equipment. The term equipment nents and is Failed (down) if and only if at will be used to designate an element of a least k of them are Failed (down). system whose failure and repair characteristics are considered as those of a unit and not as a 6-3.3 DERIVATION OF A RELIABILITY collection of smaller elements. DIAGRAM 7. a. Up.

An equipment or system is The process of deriving a reliability block up if it is capable of performing its function. diagram (for s-reliability without repair) from b. Degraded. An equipment or a detailed system description is a complex system is degraded if it performs its function, process that involves many factors. This but not well. process must be analyzed to establish stand- 8. Down. An equipment or system is aidized procedures which form the basis of a formal mathematical technique. The analysis, down if it is incapable of performing its func- using a part of a tropospheric scatter system, tion. is described in the paragraphs that follow ) 9. Design Redundancy. A system has (Ref.

2). design redundancy with respect to a given set of equipments if the system is up with only a Fig. 6-12 illustrates the equipment config- part of the set in operation, i.e., the extra uration for the receive function of a tropo- equipments are solely for the purpose of im- spheric station. Fig. 6-13 is the dependency proving the reliability and availability charac- diagram and Fig. 6-18 is the reliability dia- eristics of the system. gram for the system in the particular mode being analyzed. The tropospheric system is 10. On. An equipment which is up and complex and c.n operate in several modes. in operation is on. Each mode has a different reliability diagram. 11. Idle.

An equipment which is up and The possible modes are: not in operation, i.e., being held in standby is 1. Voice Set Group output consists of idle. outputs from 14 to 24 physically available 12. Block. A Block is a grouping of n channels of which nine or more must be up. identical equipments. The reliability of the (This statement on the dependency diagram grouping depends only on the number of implies two reliability diagrams.) If more than equipments which are up in the block and not nine Voice Sets arp up, the reliability diagram on which equipments in the block are up. shows them in parallel. If nine Voice Sets are 13. Sections.

A Section is an s.indepen- up, the reliability diagram shows them in se- ies. dent grouping of equipments within a system. A system is divided into sections when the 2. The output from any specific voice set number of system up-states is so large that functionally depends on that particular voice computer calculations are difficult. For ex- set AND on the output from any of the 24 ample, calculation of system MTF with repair Channel Filter outputs AND on the output \ requires an inversion of the state matrix. If from "Engine Generator Set 1 OR Engine the computer available to the analyst cannot Generator Set 2". (The parallel group of 6-23