US Army Materiel Command AMCP 706-197 — AMCP 706-197 Reliability Prediction Handbook — US Army Engineering Design Guide PDF

Downloaded from https://www.everyspec.com At" 708-137 quences. In complicated systems, the designer (by some authors) just by the word redundan- might be quite surprised at what happens; sit- cy. uations easil y can arise that the designer never A warm unit has a failure rate somewhere dreame'!- 1. between a hot unit and a cold unit. Often it is Reconfiguration of the system to operate taken to be the general case and includes hot in a degraded mode after a failure and before and cold as limiting situations. a repair is effected is often a desirable situa- In some analyses where the units always tion.

A computer for example might contin- are working, the individual failure rates de- ue to operate but at a lower speed during the pend on the number that are working. A con- 5 min it takes to remove and replace a unit. A ceptually simple example is several induction communication system might slow its message motors (tied firmly together so that their rate during switchover. The slew rate of a shafts are effectively in line). Suppose the fail- hydraulically powered system might drop to ure mode is insulation failure due to tempera- one-third its usual value while a redundant ture rise and there are six high-slip S hp mo- part of the pumping system is being replaced. tors driving a 20-hp load.

The temperature As a matter of practical fact, a designer rise of the operating motors will depend on will make many decisions without using much the number of operating motors. Allow 10 more than the engineering judgment of him- percent for nonuniform distribution of load. self and his associates (staff or line). There is Then the maximum load on each motor when not enough time, money, or people to analyze six motors are operating is (20-hp/6) X 1.1 = everything. 3.7-hp; for five motors it is 4.4-hp; for four motors, it is 5.5-hp; ,nnd for three motors, it is 7-5 FAILURE BEHAVIOR OF SPARES 7.3-hp.

Obviously, the insulation will degrade AND OTHER PARTS mnuch faster as the number of motors is re- duced. At nominal 7.3-hp load, the current The terminology in this field is very con- would probably be high enough to kick out fusing because it has grown like Topsy. The the oo, rloads. Another example is a commu- best terminology seems to be cold-warm-hot nication system. If radio receivers are han- spares; it is flexible and is not confused with dling traffic in parallel, the failure rate of each other aspects of system design.

The crux of receiver is probably independent of the num- the matter is the failure behavior of the units; ber of units which are operating, unless heat but some of the terminology refers to the use dissipation is a critical factor. of the unit and only indirectly implies the it is a cribe redun- failre ehaior Th remindr o ths pra-It is best to use a term to describe redun- failuredancy which indicates the failure rate behav- graph presumes constant failure rates. More- ianot the operati reduv- complicated failure distributions can be dis- ant e unit I cussed, but the origin of time must always dant/spare unit.

then be kept track-of for every unit-a diffi- 7-6 STYLES OF REDUNDANCY cult task indeed. A cold unit has zero failure rate. This is There are at least three styles of creating not a likely situation because spares in stor- redundancy: age, etc., do deteriorate. But it is very tract- (1) k-out-of-n systems 9 able in an analysis. This is the same as pas- (2) Voting techniques sive-redundancy. In many cases it is what an (3) Other. author means by standby-redundancy (unless The "Other" category includes combinations he has otherwise specified the failure behav- of the first two, and multiple units which do ior). not easily reduce to k-out-of-n.

Hammock A hot unit has the same failure rate as an (bridge) networks are in the latter category. It operating unit, regardless of whether it is ac- is most important to distinguish between the ,, tually in operation or not. This is the same as physical system and the logic chart used to active redundancy. It is sometimes implied describe the physical system. The description 7-3