Iveco — EuroCargo E4 BODYBUILDER INSTRUCTIONS

Print 603.93.431 Base - July 2006 Revi - June 2007 EUROCARGO EURO 4 - 5 FITTING SUPER STRUCTURES 3-53 Table 3.17 — Installation of tail lifts, maximum permitted bending moment (subframe fixing with shear-resistant plates) Strength modulus Wx (cm3) of subframe section Model A x B x t (mm) /mm2) ame 16 19 21 26 31 36 46 57 89 105 119 (N R0,2 subfr Permitted static bending moment (kNm) ML60, ML65, ML75, ML80EL 172. 5x65x4 240 35.7 39.4 44.2 43.5 46.8 52.6 56.4 (60.8) 360 44.7 50.5 52.5 54.4 (58.3) (60.1) (67.1) (74.8) ML60, ML65, 240 39.0 42.9 47.9 46.9 50.4 56.7 (60.5) (65.0) ML75, ML80EL 172. 5x65x5 360 48.7 56.3 (59.8) (58.7) (63.0) (70.8) (75.7) (81.3) ML80, ML90, ML100 195.

5x65x4 240 41.3 45.5 50.9 49.9 53.5 60.2 64.0 (68.4) 360 51.7 57.6 59.6 62.3 (65.6) (67.6) (74.6) (82.4) ML80, ML90, ML100, ML110EL, 240 45.2 49.6 55.2 53.9 57.8 (64.8) (68.7) (73.2) ML120EL 195. 5x65x5 360 56.5 65.1 (69.1) (67.4) (72.2) (81.0) (85.9) (91.5) ML110EL, ML120EL 195. 5x65x6 240 48.6 52.2 53.3 56.9 58.2 60 65.8 72.1 360 67.3 72.3 73.8 78.8 80.6 83.2 41.1 99.8 ML120, ML130, 240 60,1 65,4 726 70,3 75 83,9 87.8 92.3 ML150 240x70x5 360 75.1 85.8 90.7 87.9 93.8 (104) (109.7) (115.4) ML120, ML130, ML150 240x70x6 240 65.3 70.9 78.2 75.5 80.4 89.6 93.4 98.0 360 81.7 93.0 97.7 94.4 (100.5) (112) (116.8) (122.5) ML120, ML130, 240 68.9 74.6 81.9 79.0 84.0 93.4 97.1 (101.7) ML150 240x70x6.

7 360 86.1 98.0 (102.4) (98.8) (105) (116.7) (121.4) (127.1) ML150 240x70x7. 7 240 74.2 82.4 86.1 84.0 88.6 94.8 101.7 117.5 360 102.8 114.0 119.2 116.2 123.0 131.3 140.8 162.8 240 59.1 65.4 70.4 68.0 72.5 80.4 84.0 88.4 109.3 115.9 116.8 ML180 262. 5x80x6 360 77.6 85.8 92.4 89.2 95.2 105.5 110.3 116.1 (143.3) (152.1) (153.3) ML180 262. 5x80x6. 7 240 62.5 68.9 74.0 71.4 76.0 84.0 87.5 91.9 113.2 119.9 120.6 360 82.1 90.5 97.2 93.6 99.7 110.2 114.9 120.9 (148.5) (157.4) (158.3) 240 67.4 73.9 79.1 76.0 80.8 89.0 92.4 96.7 118.4 (125.2) 125.7 ML180 262. 5x80x7.

7 360 88.4 97.0 103.8 99.8 106.0 116.8 121.3 (126.9) (155.5) (164.3) (165.0) If the height of the subframe profile has to be reduced, using shear resistant connections between chassis and subframe, combined section profiles can be used, as shown in Table 3.16, instead of the C-profile, provided that the flange width and thickness are not less than the corresponding values of the profile indicated in the table. The above are general conditions which apply to the materials indicated in Table 3.18. To assess whether it is possible to use materials with higher mechanical specifications, it is necessary to check the total resistant moment of the chassis plus subframe.

Table 3.18 - Solutions with combined section reinforcing profiles (see Figure 3.30) A B C D R0,2 (N/mm2) 320 320 360 360 Maximum reduction of height of profile 40 60 100 120 (mm) LV (see Figure 3.32) 0.50LU 0.60 LU 0.80 LU 0.85 LU LH (see Figure 3.32) 0.60LU 0.65 LU 0.95 LU 1.00 LU Example of combined profiles as alterna- tive to a 250x80x8 (mm) C-profile 210x80x8 190x80x8 150x50x8+ angular element 130x50x8+ angular element Effective height reduction (mm) 40 52 92 104