U.S. Army Material Command (AMC) AMCP 706-210 — FUZES - Engineering Design Handbook AMCP 706-210 (U.S. Army) PDF Download

Downloaded from https://www.everyspec.com AMCP 706-210 pressing on~the pin. The equation ofamotion'for acceleration inuit be greater than that resulting -the pin- is-sinilar to Eq. 6-12 where j is 0.25-lb 'from a drop but less than that produced by a and a' is 10 g. To solvefor tie-time to move the properly fired projectile (see par. 6-5.4l. distance - , the initial compression of the T'e three-leaf mechanism used as the hafety spring x, must be known. This is typical of de- device in the 81 mil Mortar Fuze, M532, is sign problems: assumptions are made, computa- shown in Fig 10-3. Operation is as follbws:

Upoit tions are performed, and-ihen the original dimen- setback, the first leaf turns against its spring. sions are corrected if necessary. When- it rotates far enough, it permits the second Hence, if x0 is 1.5 in. and. if the pin must leaf'to rotate, and that in succession releases the move 0.029 in. (1/4 of 0.116 in.), the time-inter- last leaf. The last leaf moves out of the way to ,val will be 1.1 10 " ' zec from Eq. 6-12. low far release the armingrotor. will thesetback pin move in this time? Fig. 10-2 The mechanism utilizes a large portion of the shows the pertinent dimensions for the setback area-under the acceleration curve because succes- pin. Let the spring constant be 1.31 lb/in.

and sive leaves are assigned to successive portions of the pin weight 0.0022 lb. To obtain the greatest the curve (seeFig. 6-19). Each leaf is designed to distance that the pin will move, the, effects of operate at a slightly different minimum accelera- friction are -neglected; in that case Eq. 6-5 will tion: level by-using identical springs with geomet- serve-in which:.x is-approximate:] 0.45 in. Thus rically similar leaves of different thicknesses. x = 0.39 in. whichmeans that the pin will move Eachleaf operates when it experiences approxi- .0.06 in. Therefore,, the setback pii must be mately half of the-average acceleration occurring ,bottomed at, least 0.060 in.

away,,from tljzsafety in theqinterval to which it- is assigned For examr- ,-" The setback pincwill strike the safety pin some experiences an acceleration of approximately e, time later-than 1.1 msec, and the pin Will not be 450 g for 2.5 msec. The total d-sign .velocity. able to re-enter the hole; hence the fhze will con- change is approximately 1-10 ft/sec. finue to arm; The mechanism, has beeri shown to be safe, when subjected to 40-ft drops. 'This safety re- 10.2.2 SEQUENTIAL LEAF ARMING, sults-from the fact,that the irpact velocity in a 40-ft drop (about 50 ft/sec) is less than half- tle For projectiles that do not rotate, armingis design velocity-change for the mechanism.

How- 'usually accomplishedby setback forces. The mo- ever, the parachute drop-imposes the mosustrin- tion 6f sliders arid rotors that is impeded by set- gent requirements on this mechanism. It speci- back.:canb e:usedtoachieveboresafety. Acceler-- fies that the46zeimust-w;thstand the ground irri- ,aions-resulting from a drop are higher (Fig.1 5-5) pact forces that -esult -when, it isdelivered by but are not sustaindd-as long as those resulting -parachute. The mechanism will prevent arm.ihg ;frorft firing (Fig. :5-2).'Hence, many.

devices are when the--amriwinition-,,isdelivered byca-properl built to discriminate between firing.setback and functioning parachute because the imjthct veloc- inpact forces due to drops. ity is less than that !for a 40-ft free-fall 'drop. perhaps the esiest way to discriminate ,be- However, if the- pardchute malfunctions during tween -the two is, to build a device that is-actu, delivery, the velocitychange atimpact is greater ated only by the accelerations present under fir than the-design velocity change.

It is, therefore, ing conditions.,, An approximation to-'this accel- possible that ai foiled parachute delivery could eration, an be obtained with -a, sequential leaf produce the-minimum design acceleration for , mehanism 2 . The main featureAn its design is length of time sufficient to arm the mechanism. the requirement of an extended acceleration,, much longer than that presentjh a- drop ifipact into aity medium usually encountered. With-a 10-3 FUZE COMPONENTS FOR SPIN-STABI-, provision for- return to the unarmed' positiot, LIZEDPROJECTILES 'this device can- withstand many drop impacts without becoming committed to arm.

The ariningoperations of munitionsstabilized Sequential'leaf mechaftisms are designed to re- by spin may -make use of, the forces due to spond -t A threshold acceleration sustained for the spin on the fuze parts. Sliders ah'be moved some period of time. The product oftime and by the centrifugal force -field, rotors nay be - pin. -ple, the :first leaf -is designed to operate when it 10-3