U.S. Army Material Command (AMC) AMCP 706-210 — FUZES - Engineering Design Handbook AMCP 706-210 (U.S. Army) PDF Download

Downloaded from https://www.everyspec.com AWCP 7dO-' APPLIEO FORCE For purposeS of reliable initiation, the designer -may pr~fer to place the detonator at th, hposition in which the, firing pin has the maximum -kinetic SPRING "tions based 6nthe above equations 3 . Suppose a reversing Belleville spring is needed PIN fora mineihatls actuated by.aminimum force of 35, Ib. According to the space-available do JI :, do, - " may be 2 -in. and d = 0.5 in. For nonmagnetic PRIMEand nonmetallic mines a- phenolic laminate i -' = 13.5 x lW s psi,,v = 0.3), iS used for the- ts " , -energy. This position is found by further derivas, (A) Applicatioh of FOrce spring material.

This leaves the spring height-h and'th-ethickness t to be deterined. Eqr 13-2 gives the deflection y for'imaximum pressurein terms of,handjt. As' trial let t, = 0:025 in. and h -0.25 in. so that y bedomes'0.107in. Substi- tutibn ofthese values in Eq. 13-1 gives the maxi- mum spring force F as 144'1b which, is too great for a 35 lb actuating-force. For a second ,trial; h is reduced to 0.15 in. from which y at, the miaximum load becomes 0.066 im Then from Eq. 13-1, the maximun (8)India/ion of Primer force becomaes 31 lb. This valuefalls' withinthe specifiedliiit. Figure 131.

Action of Reversihg Belleville Soring It remains to determine whether the spring material will withstand the stresses caused by this load. Eq. 13-4 indicates that the maximum 2(132) stress 'in the spring oax is 49;000 psi which is , h- /h 2 not excessive for a phenolic laminate. rial; . 'is the leaftthickness, y is the spring deflec- ,tion,,h-isothe initial distance-ofthe.leaf.from~the where E is the-moduilus Ofeiasticity of the mate- 13.2.3 PULL-RELEASE TRIGGER center point (see Fig. 13-1), v is Poisson's ratio 'Tntes'th6 iuse 'i a tri ha...ii m aretrates the use of a trip wire.,One foa land mine for themaer d isthe mater d. inner is shown -in Fig. 13-2'.

The main fuze body is diameters, respectively. B ,s the foliowing pa- mounted' firmly to the mine. The trip wire is rameter stretched across he expected path of enemy ad- 6 (d - d4) 2 . vance and the slack taken -up by turning the B= (13-3) knurledknob. The safety cotter pin is removed 0 d In (d/d ) and the device cocked by turning the, knurled knob until the safety pin can be removed from Maximum stress-'ar 0ccurs on- the inner edge its slot. The shoulder on the safety pin andthe of'the spring when y = h and is given by safetywire are interlocks that require 'the device d. 0 _ d 0 i to be armed 'in this sequence. The device is now 4Eh- '7___ d. readyt betriggdred..

(an - 2 d d The pull-release device also serves to provide 2 n (d. -d )2 (13-4) an antiremoval feature. When the mine is buried d 1 / 0 in the,giound, the device isplanted-on the mine t' with the Wire attached to the ground. Personne, +2 d (d o + d 1 ) who remove the mine will set the-fuzeoff. The essential part of the trigger is an expansible socket shown schematically in Fig. 13-3. When a 13-2