Downloaded from https://www.everyspec.com AMCP 706210 Piezoelectric transducers and electzomagnetic pact switch or other device can discharge the geeratos are possibilities for converting the capacitor through the detonator to cause deto. abundant mechanical energy available in a missile nation. Delay time will be a function of the RC or projectile into sufficient electrical energy. time constant of the circuit. Various forms of batteries that convert chemical Piezoelectric elements are usually mounted in or atomic energy into electrical energy have also either the nose or the base of a projectile. Fig. proven successful. In addition, a precharged con- 3-4 shows a nose-mounted configuration.
Electri. denser makes a satisfactory power source, cal connections are brought out from the faces of the disk. One side of the disk is grounded and the 3.4.3.1 Piuzoek04ot Tauduuaes other side is connected to the fuze base element by an insulated wire that passes through the high When a piezoelectric element is stressed me- explosive. To eiiminate the wire connection, it chanically, a potential difference will exist across is sometimes possible to use parts of the fuze as the element which will cause a charge to flow in an electrioal connection between the nose- the circuit. One common method of manufac- mounted element and the detonator.
Any parts turing such transducers is to form a polycrys- used for this purpose must be adequately insu. talline piezoelectric material into a ceramic. lated from the Pize housing. These ceramics can be formed into any desired shape, such as a disk. For actual use in a circuit, ,oNCCP cMA- the faces of the ceramic body are usually silver- coated to form electrodes. In general, the voltage across such an element is proportional to the product of stress and element thickness while L the charge per unit area produced is proportional to the applied stress. The voltage is developed immediately when the element is stressed. A straightforward use of a piezoelectric trans- Figure 3-4.
Piezoelectric Nose Element ducer is to place it in the nose of a projectile. On A somewhat simpler arrangement, in which impact, the element will be stressed and a voltage the element is mounted in the base of a round, pulse will be supplied directly to an electric ini- is shown in Fig. 3-5. This arrangement also tiator. The element must be designed to provide eliminates the connecting wire and results in a the proper voltage. A word of caution--it is pos- self-contained base fuze.
Mounting the element sible to generate high voltage (10,000 volts) up- in the base, however, requires that it be stressed on target impact, which will break down the by the impact shock wave transmitted to the electrical insulation thereby grov-ding out the base along the walls of the projectile. initiating pulse. In some applications, the complete fuze, in. Piezoelectric elements are stressed on impact. cluding the piezoelectric element, Is mounted The signal is transmitted at once in those appli- in the nose of a round. As in the case of the base- cations where it is desired to function the fuze a mounted element, this results in a self-contained very short time after impact.
In HEAT projec- fuze. Care must be taken to prevent the fuze tiles, for example, the main explosive charge from being damaged at impact, particularly in must be detonated before appreciable loss of applications where a delay-after-impact feature stand-off results from crushing of the ogive or is incorporated. before deflection occurs from the target at high Quite often, better performance can be ob- angles of obliquity. This necessitates a fuze func- tained by usir two or more elements connected tion time of 200 u sec or less after impact ' in electrical parallel rather than a single element.
These elements have also been used in appli- To reduce the possibility of premature fuze cations where delay after impact is specified. function, a bleeder resistor is normally con- To accomplish this, the energy pulse generated nected across the piezoelectric element to dissi- by the element at impact can be applied to the pate any electrical charge that it might accumu- detonator through a delay network. Another late during storage or as a result of stress induced possible solution is to stress the element on by setback or spin. The value of the bleeder re- firing to charge a capacitor. At impact, an im- sistor must be high enough to insure that most 3.6