Downloaded from https://www.everyspec.com AMCP 706-210 components because it is too hazardous to between a delay and its primer to reduce blast handle large quantities of primary explosive in effects and particle Impingement. In general, a single package. Hence, for safety in manufac- increasing the free volume between these two tur and assembly of ammunition, the txpiosive will make initiation more difficult. Decreasing train consists of several small components. confinement of the delay column will have the In military items, the smaller, more sensitive same effecL.
charges are isolated from the larger ones for HIash detonators and relays are sometimes in- safety in handling until the item is armed. Again itiated from a distance by a primer, a delay, or as pointed out earlier, mechanical desig ccnsid- even another detonator. In this problem particu- erations indicate the advisability of small corn- lady, precise performance data are difficult or ponents and chemical kinetics design considera- impractical to obtain.
The alignment of the two tions indicate that the most effective explosive components is probably most important to suc- material for oie component is not neceesarily cessful initiation, if the air gap is confined, it the most effective for another; these considera- should be at least as large as the detonator diam- tions result in further subdivision of the explo- eter and perhaps slightly larger. sive charges. - Since quantitative da~a for any particular con- In the course of the growth of each detona- dition do not exist, trial and error methods must tion, discontinuities are met. Transmission of a be used in design.
A convenient method to de- detonation across a discontinuity is affected by cide upon the adequacy of a given system is to a wide variety of factors including the proper- vary the charge weight of the initiating compo- ties of the explosive employed, the density at nent to find the marginal condition for initiation. which the explosive is loaded, the material con- G.nerally, the designer chooses a component fining the explosives, the size and geometry of with double the marginal weight. each charge, the relative positions of charges, After the amplification of the explosive- and the nature of intervening materials.
The per- impulse has carried through several components mutations and combinations of these and other in the train and a detonation has been produced, factors are innumerable. Data on all of the vari- even more care must be exercised to complete ous combinations of interest cannot be obtairnad; the process. Initiation of a tetryl lead from a in some cases, because of interactions, data that detonator is indicative of the types of problem are available are apparently conflicting, encountered. Once again, confinement is most important.
A heavily confined charge can re- 4-5.2 PROBLEMS IN EXPLOSIVE TRAIN DESIGN liably initiate another explosive component, whereas a charge of twice that amount would be In the course of designing the train, many required if it were unconfined. Empirical data problems arise such as determining sizes of the obtained under various conditions indicate that various components, packaging each one, spacing the effects of confinement are optimum when or positioning them, and, most important, mak- the wall thicknesb of the confining sleeve is ing use of the new charactei istics created by this nearly equal to the diameter V the co'llmn. On train effect.
the other hand, the nature of the confining In fuzes employing delay elements, primers material is nearly equally important. Data have which produce essentially a flame output are been obtained which show that a detonation used to initiate the deflagration. It is some- can be transferred across an air gap nearly times necessary to initiate delay mixes across a twice as far if the donor is confined in brass or sizable air gap. Such an arrangement is practical steel rather than aluminum Relative data on but care must be taken to avoid destroying the gap distance for various acceptor-C iarge con- reproducibility of the delay time. If initiation fining materials are:
steel-13, copper-7, and from the primer is marginal, delay times may aluminum-4. become long. On the other hand, the delay time In fuze explosive trains,,one seldom works may be considerably reduced if particles from with unconfined charges. The explosive compo- the primer imbed themselves in the mix (thus nents used are nearly always loaded into metal effectively shortening the delay column) or if cylinders or cups. Even this relatively thin-walled the delay column on disrupted by the primer confinement gives considerable improvement blast. Frequently, a web or baffle is employed over air confinement in transmitting or accepting 4-13 i I