Ramsey Electronics · OM2 · 22 pp.
Ramsey Electronics OM2 Optically Isolated Interface Manual PDF
Related manuals
Document text
OPTICALLY ISOLATED INTERFACE Ramsey Electronics Model No. OM2 The OM2 provides 5000 volts of electrical isolation between the input and output signals. Any input signal, AC or DC, greater than 1.5 volts can be used to provide an output signal up to 40VDC at up to 150mA. The output can follow an input signal with a frequency from 0Hz to 250KHz or it can provide a constant level when an input signal is applied. AC or DC input 40VDC @ 150mA output 0Hz to 250KHz operation Output can either follow AC input or “latch” with signal input Over 5000 volts optical isolation between input and output signals Full custom configuration instructions included OM2 1 1
PARTIAL LIST OF AVAILABLE KITS:
RAMSEY TRANSMITTER KITS FM10C, FM25B FM Stereo Transmitters AM1C, AM25 Transmitter RAMSEY RECEIVER KITS FR1C FM Broadcast Receiver AR1C Aircraft Band Receiver AR2 Aircraft Band Receiver SR2C Shortwave Receiver AA7C Active Antenna SC1C Shortwave Converter RAMSEY HOBBY KITS SG7 Personal Speed Radar SS70C Speech Scrambler/Descrambler TT1CTelephone Recorder MD3C Microwave Motion Detector PH14C/15C/16C Peak hold Meters RAMSEY AUDIO KITS SHA1C and SHA2 Headphone Amplifier kits UAM4 40 Watt Stereo Amplifier kit RAMSEY AMATEUR RADIO KITS HR Series HF All Mode Receivers DDF1 Doppler Direction Finder Kit QRP Series HF CW Transmitters CW7C CW Keyer QRP Power Amplifiers RAMSEY MINI-KITS Many other kits are available for hobby, school, scouts and just p kits are always under development.
Write, call or visit www.rams our free Ramsey catalog. OM2 Ramsey Electronics publication No. OM2 Rev1.0a First printing: March 2010 This Printing: May 2011 COPYRIGHT 2010 by Ramsey Electronics, LLC. 590 Fishers Station Drive, V 14564. All rights reserved. No portion of this publication may be copied or dupli written permission of Ramsey Electronics, LLC. Printed in the United States of OM2 2
OPTICALLY ISOLATED INTERFACE TABLE OF CONTENTS Introduction/Circuit Description ...................... 4 Parts Layout Diagram ..................................... 7 “Learn-As-You-Build” Kit Assembly ................ 8 Parts List......................................................... 9 Assembly Steps ............................................ 10 Schematic ................................................ 12-13 Input Signal Level Configuration .................. 14 Final Configuration Assembly Steps ............ 15 Configuring Your OM2 .................................. 16 Conclusion ....................................................
21 Specifications ............................................... 22 Ramsey Kit Warranty ................................... 23 Ramsey Publication No. OM2: Manual Price Only $5.00 INSTRUCTION MANUAL FOR RAMSEY ELECTRONICS, LLC 590 Fishers Station Drive Victor, New York 14564 Phone (585) 924-4560 Fax (585) 924-4555 www.ramseykits.com OM2 3
Introduction The OM2, Optically Isolated Interface, provides an optically isolated interface between two devices. It can be used to interface nearly any AC or DC signal to a logic level signal. It can also be used to operate a relay upon detection of an input signal. The really great thing about the OM2 is the input and output are totally isolated from each other. Virtually any voltage input level above 1.5 volts can be used as long as long as the input current is limited to a maximum of 60mA. The input can be a simple DC level or an AC signal with a frequency up to 250KHz.
(That’s 250,000 cycles per second for the old pre-Hertz folks.) The input and output are isolated from each other to 5000 volts AC(rms) difference between the input and output connections. The output can drive up to 150mA at up to 40VDC. It even provides active low and high outputs when the input is activated. Theory of Operation The heart of the OM2 is an optical coupler. An optical coupler contains an infrared LED and a photo transistor. When the LED is turned on it causes the photo transistor to turn on. The coupler used in the OM2 actually has two LED’s on the input. These LED’s are connected in parallel with each other in opposite directions.
This makes it able to operate using either a DC or AC input. The DC polarity of the input doesn’t matter since one of the LED’s will be turned on when an input signal is applied regardless of polarity. We’ll take a look at the schematic now and go thru the entire circuit operation. The Input Circuit On the left side of the schematic you will see J1 which is the input connection. The input signal is applied to J1’s two pins. Starting at pin 2 of J1 you will see resistors R1, R2 and capacitor C2 connected in series with each other. These components act to limit the current supplied to the LED’s in OC1 pins 1 and 2.
The LED’s in OC1 are just like any other LED in that the forward current must be limited, in this case to a maximum of 60mA. Why are there two resistors and a capacitor you ask. Well we tried to give you lots of options to configure the OM2 to meet your requirements. The values shown for R1 and R2 are such that you can use a standard 110VAC or 220VAC signal to trigger the output. Since the original concept for the OM2 was to sense presence or absence of power on an AC power line it made sense to provide a simple way to select the input voltage by either having both resistors in place for 220VAC or to remove R2, by installing JMP1, to change to 110VAC.
Notice they are both the same value and 220VAC is twice 110VAC so the current is changed by a factor of 2 by adding or removing one of the resistors. The “Configuring Your OM2”section of this manual explains how to set up the input of the OM2 for your application+. But what’s C2 there for? OM2 4