VLT ® 2000 Series I References 200 FREQ RANGE 2 ) Operation and display 000 LANGUAGE S ) I I Inputs and outputs 402 INPUT 18 S ) Factory settings and service ENGLISH 001 MENU SETUP S ) 120 Hz 201 MIN. FREQUENCY 2,S ) START 403 INPUT 19 S ) SETUP 1 002 MENU SET COPY 0 202 MAX. FREQUENCY 2,S ) REVERSING 404 INPUT 27 S ) DO NOT COPY 003 LOCAL/REMOTE S ) 50 Hz 203 JOG FREQUENCY 2,S ) MTR.COAST not 405 INPUT 29 S ) REMOTE 004 LOCAL S ) 005 VALUE AT MAX S ) 10 Hz 204 DIG. REF. TYPE S ) JOG 408 LOG OUTPUT 46 2,S ) SUM 205 DIGITAL REF. 1 2,S ) UNIT READY 409 RELAY OUT 01 2,S ) 1000 006 LOCAL RESET S ) UNIT READY 411 ANALOG REF TYPE 2,S ) ENABLE 007 LOC START/STOP S ) 0 206 DIGITAL REF.
2 2,S ) ENABLE 008 LOCAL FWD/REV S ) 0 207 DIGITAL REF. 3 2,S ) LINEAR 412 INPUT #53 2,S ) DISABLE 009 LOCAL JOG S ) 0 208 DIGITAL REF.
4 2,S ) 0 - 10 VDC 413 INPUT #60 2,S ) ENABLE 010 LOC REFERENCE S ) 0 209 CURRENT LIMIT 2,S ) 0-20 mA Section 1 Section 2 Section 3 ENABLE 013 DATACHG.LOCK Depending on unit 210 LOW FREQ WARN 2,S ) I Serial data interface 500 ADDRESS 0 Hz 211 HI FREQ WARN 2,S ) 01 501 BAUD RATE NOT LOCKED 120 Hz (from 200) 213 HI CURR WARN 2,S ) 1200 K 502 DATA READ-OUT S ) REFERENCE% 503 COASTING S ) I Load and motor 101 SPEED CONTROL 2, S ) I VLT,MAX (from 209) 215 RAMP UP TIME 1 2,S ) SLIP COMP 102 CURRENT LIMIT S ) 5 s 216 RAMP DOWN TIME 1 2,S ) LOGICAL OR 504 Q-STOP S ) PROGRAM SET 103 MOTOR POWER 2 ) 5 s 218 ALT: DOWN RAMP 1 2,s ) LOGICAL OR 505 DC-BRAKE S ) NOM.
SIZE 104 MOTOR VOLTAGE 2 ) LOGICAL OR 506 START S ) Depending on unit 105 MOTOR FREQ 2 ) 1 s 224 CARRIER FREQ. 2,S ) LOGICAL OR 507 DIRECTION S ) 50 Hz 107 MOTOR CURRENT 2,S ) 4.5 KhZ 230 SPEED UP/DOWN S ) DIGITAL 508 RESET S ) Depending on unit 108 MOTOR MAG.AMP.
2,S ) DISABLE LOGICAL OR 509 SETUP SELECT S ) Depending on unit 109 START VOLTAGE 2,S ) I Functions and timers 300 BRAKE OPTION S ) LOGICAL OR 510 SPEED SELECT S ) Depending on unit 110 START COMP 2,S ) NOT APPLIED 306 DC-BRAKE TIME 2,S ) LOGICAL OR 511 BUS JOG 1 S ) 0 s 307 DC-BRK FREQ 2,S ) 10 Hz 514 BUS BIT 4 S ) 0 111 U/F RATIO 2,S ) 1 Hz 308 DC-BRK VOLTAGE 2,S ) Depending on unit 112 SLIP COMPENSATION 2,S ) 10 V 309 RESET MODE S ) QUICK STOP 516 BUS REFERENCE S ) Depending on unit 114 FEEDBACK TYPE S ) MANUAL 310 TRIP DLY@C.LIM S ) 0 517 STORE DATA S ) CURRENT 119 FEEDFWD FACTR 2,S ) INFINITE 315 MOTOR THERMAL 2,S ) OFF 100% 120 CONTRL RANGE 2,S ) I Service and display 606 TOTAL OP HRS.
607 RUNNING HRS. 608 NO. POWERUPS 609 NO. OVERTEMPS 610 NO. OVERVOLTS 100% 121 PROPRT/L GAIN 2,S ) PROTECT-OFF 0.01 122 INTEGRAL TIME 2,S ) OFF 125 FEEDBACK SCALE 100% 2 ) Can be changed in both setups S ) Can be changed i Start mode (running motor) MG.20.B6.02 – VLT is a registered Danfoss trademark 105