Department of Defense · 5 pp.

Department of Defense S38784 NOTICE 1 COVER PAGE

Related manuals

Document text

Downloaded from https://www.everyspec.com NOT MEASUREMENT SENSITIVE NOTICE OF CHANGE MIL-STD-1808A NOTICE 1 8 February 2002 DEPARTMENT OF DEFENSE INTERFACE STANDARD SYSTEM SUBSYSTEM SUB-SUBSYSTEM NUMBERING TO ALL HOLDERS OF MIL-STD-1808A: 1. THE FOLLOWING PAGES OF MIL-STD-1808A HAVE BEEN REVISED AND SUPERSEDE THE PAGES LISTED: NEW PAGE DATE SUPERSEDED PAGE DATE Title 1 December 1996 Title Reprinted without change ii 8 February 2002 ii 1 December 1996 1 8 February 2002 1 1 December 1996 2 8 February 2002 2 1 December 1996 2. RETAIN THIS NOTICE AND INSERT BEFORE TABLE OF CONTENTS. 3. Holders of MIL-STD-1808A will verify that page changes and additions indicated above have been entered.

This notice page will be retained as a check sheet. This issuance, together with appended pages, is a separate publication. Each notice is to be retained by the stocking points until the standard is completely revised of canceled. Preparing Activity Air Force - 16 (Project: TMSS-F642) Review Activities Air Force - 10, 11, 13, 19, 99 AMSC N/A AREA TMSS DISTRIBUTION STATEMENT A . Approved for public release; distribution is unlimited.

Page 1

Downloaded from https://www.everyspec.com NOT MEASUREMENT SENSITIVE MIL-STD-1808A(USAF) 1 December 1996 SUPERSEDING MIL-STD-1808 10 October 1990 DEPARTMENT OF DEFENSE INTERFACE STANDARD SYSTEM SUBSYSTEM SUB-SUBSYSTEM NUMBERING AMSC N/A AREA TMSS DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited . REPRINTED WITHOUT CHANGE

Page 2

Downloaded from https://www.everyspec.com MIL-STD 1808A(USAF) FOREWORD 1. This standard is approved for use by the Department of the Air Force and is available for use by all Departments and Agencies of the Department of Defense. 2. In order to provide standardization between publications a standardized numbering system has been developed. It is was designed with sufficient flexibility to permit expansion and application outside the technical manual system to support logistics elements that interact with or directly influence equipment maintenance and technical manual development and use. 3. To ensure maximum flexibility, gaps have been left in the system and subsystem numbering sequences.

Manufacturers are encouraged to use the unassigned systems and subsystems to accommodate unique design or emerging technologies when required, as approved by the procuring activity and current acquisition policy. 4. As a minimum, this standard is intended to be used in conjunction with MIL-PRF-83495 and MIL- ' HDBK-863. Additional applications are available as defined in the documents identified in section 2. ' 5. Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to:

MSG/MMF 4375 Chidlaw Rd., Suite ' S008, Wright Patterson AFB, OH 45433-5006, by using the Standardization Document Improvement ' Proposal (DD Form 1426) appearing at the end of this document or by letter. SUPERSEDES PAGE ii OF MIL-STD-1808A ii

Page 3

Downloaded from https://www.everyspec.com MIL-STD 1808A(USAF) 1. SCOPE. 1.1 Scope. This standard sets forth requirements for the system, subsystem, and sub-subsystem numbering requirements for engineering drawings, technical manual, and other acquisition and logistics support requirements for aircraft, missile and space systems, engines, and ground communication-electronic equipment. Additionally, it may be used for supportability analysis, configuration management, maintenance data collection, or where ever a consistent maintainability related reference numbering requirement exists across a weapon system. 1.2 Acquisition applicability.

This standard shall be used by all Air Force acquiring activities and their respective contractors during the development and acquisition of weapon systems and equipment. 2.1 General. The documents listed in this section are specified in sections 3, 4, and 5 of this standard. This section does not include documents cited in other sections of this standard or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements documents cited in sections 3, 4, and 5 of this standard, whether or not they are listed. 2. APPLICABLE DOCUMENTS.

2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the solicitation (see 6.2). SPECIFICATIONS DEPARTMENT OF DEFENSE MIL-PRF-9854 - Technical Manuals:

Structural Repair (Aircraft) MIL-PRF-38807 - Technical Manuals - Illustrated Parts Breakdown, Preparation of MIL-PRF-83495 - Technical Manuals - On Equipment Maintenance Manual Set MIL-PRF-87268 - Manuals, Interactive Electronic Technical - General Content, Style, Format, and User-interaction Requirements STANDARDS DEPARTMENT OF DEFENSE MIL-HDBK-863 - Wiring Data and System Schematic Diagrams ' Preparation of (Unless otherwise indicated, copies of federal and military specifications, standards, and handbooks are available from the Standardization Documents Order Desk, Building 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094.) SUPERSEDES PAGE 1 OF MIL-STD-1808A 1

Page 4