MIL-STD MIL-STD-810B Method 513.1 / 514.1 — MIL-STD-810B Method 513.1 Acceleration & 514.1 Vibration Test Standard PDF

,. ;. Downloaded from https://www.everyspec.com . ..-’. .. .. .. . . .. . . . .MIL-S*81OB .->.. 15 @e .1967.:::. (:” KETSOD516.1 SHOCK .:. . ...-. 1. purpose.- The chock test is performed to determineif ‘equipmentis con- structed to vithstand expected dynamic shock stresses and that performancedegrada- tions or malfunctionswill not be produced by the service shock environmentexpected in handling, transportatlnn, and service use. 2. Apparatus. - 2.1 Shock machine. - The shock machine utilized for Procedures 1, III, and IV shall be capable of ,producingthe specified input shock pulse shown on figure 516.i-1 or 516.1-2.

The shock machine may be of the free fall, resilientrebound,nonresi:lient, hydraulic, compressed gas or other activatIng types. Apparatus for other procedures aye included in the individual procedure. 2.1.1 Shock machine calibration.- The actual test item, a rejected item, or a rigid d- mass shall be used to Calibr8tethe shock machine for conformancewith the specified wave shape. When a rigid dummy mass is used, it shall have the same center of gravity and the same mass as that intended for the test item and shall be installed in a manner similar to that of the test item.

(When a rigid dummy mass or re$ected item is used for calibration,the waveform during the actual test maY be scnnewhat different from that observeddur3ngcalibration. The shock machine shall then be cali- brated for conformancewith the specified vaveform. Two consecutiveshock ap@ication3 to the calibrationload shall produce waveforms which are all within the tolerance envelope given on figures 516.1-1 ant 51.6.1-2. Tne calibratingload shall then he re- moved And the shock teet performed Cm the actual test item. prodded all conditionsre- main the same,other than the substitutionof the test item for the calibratingload, the waveform shall be considered to meet the spcif ied test requirement.

The actual teet waveform sha’11be recorded for later use in a failure analysis if the test item fails. ..., ,. 2.2 Instrumentation.- The instrumentationused to measure the input shock pulse, in order to meet the tolerance requirements of tbe test procedure, shall have the characteristicsspecified In the follovingparagraphs. 2.2.1 Frequency response. - The frequency response of the completemeasuring system, from the accelerometerthrough the readout instrument,shall be as specified by fi~e 516.1-3.

Perticuler care shall be exercised in tbe selection of eecb indi- vidual.instrumentof the shock measuring instrumentationsystem in order to essure compatibilitywith the prescribed frequencyresponse tolerance. ..,. ., - ..-” .2.2.2 Accelerometer,piezoelectric.- When a piezoelectricaccelerometer.is employed as the shock sensor, the fundmaental.resonant frequencyof the accalero@er ... . shall be greater than 14,000 cps (resonantfrequencies n? 30 kc or higher.ere-recommend- cd). For suitable low frequencyresponse the accelerometerend load (cathodefollower, amplifier, or other load) shall have :thefollowing chmacteriatics: .,,;.;:;:?:. : --:..,.., ,,: ,?..:.,’:- ~, ,- :... -~. .G :: $:.:.2s.v:

.>.: :-.-+ .,, ,- .,.:-.:f?. :---n..-w:?r.:w51671-lm=: .ti??~~~a - ‘M3THOD516:1$:2 .... ....... ,._6- ..>”,.i . ..:,w,~fi-+ .1.- ..7*: .-.,:,:-., . ;. 20 October 1969 ... ,.,!fiq.? . . ;- !:..=k-z@ ....!,: -.....,., ,!. ‘#.,J ~ . -.~-.: : -: . *. @ , ... .,. :..,,.. -,.. ..+ ::.~.l- . * , ,.:;.“ ..,.’.. .,.. :.;4.:. ,. .:,, ., . . ,:.. . . ..!. . ,, ,. - ~~~ G ...-. ,- “,:..