,.. . MIL-STD-81OB .-% ..,. 15 June 1967 .. .. 1. Downloaded from https://www.everyspec.com . . /-’ ., E@ViSe dI.optest. One edge of the base of the case shall be supperted { on a sill 5 to 6 inches in height. The oppositeedge shall be raised to the specified height and alloved to fall freely. tie test shall be ,:., ,... 2. applied Once tO each edge of the base of the case (total of four drops). Cornerwise drop test. One comer of the base of the case shallbe supported on a block approximately5 }nches in height. A blcck nomi- nally 12 inches in height stall be placed under the other corner of the same end.
The opposite end of the case shall be raised to the speci- fied height at the lowest unsupported corner and allowed to fall freely. This test shall be applied ooce to each of two diagonally op~site corners of the base (total of two cornerwise drops). When the propor- tions of width and height of the case s.rssuch as to tause insist.tlity in the .ccrnenfisedmp test, edgewise drops shall be substit:.ted.iu such ir.st.~.:e$ two mere e&gevise droF.son ew,h end shall be performed (fwr C@.itor.sledgewise dI-OpSfor a ?.oialor eight edgewise drops). 3.5 Frmedure ITI. Crash au’ety tesrk.- This procedure shall be used La ~eter- mine the stmctural integrityof equipment umunting means.
‘Fnetest item or dummy lGad shall be attached by its normal points of attachment. The teSt item or dummy k.ad shali & subjected t.~tvo shocks in each direction along three mutuallype?.pndfc- ular axes of the equipment (total of 12 sh~cks). The shock pulse shape shall be in acccrdanc~ with either fi~re 516.1-I or 516.1-2, of amplitudea or iiand time duraticn c or d, as specified. There shall be--nofailure of tbe mounting attachmentand the teat item or dummy laad shall remain in plice and not creste s.hazard. However,bending and distortion shall be permitted. 3.6 Proce4me Iv. High intensity test.
- This prccedure shall be used where high acceieratia, short time duration shock excitatIcn results from handling, stage ignition, separation,re-entry, and/or high velocity aerodynmnicbuffeting experienced ( by missiles andfor high performance weapor.systems. Two shocks shall be applied to the test item in each direotion slag each of three mutually perpendicularaxes (total of 12 shocks). The shock pulse shape shall b+ in aceordemce with either figure 516.1-1 or 516.1-2, of amplituie a or b and time duration c or d, as spscified. The test item shall be operatIng during the test if required by the equipnent specification.
At the conclusion of the test, the test item shall be operated and the results comparedtitb the data obtained fn accord8ucewith section 3, General Requirements,parsgraph3.2.1. The test item shall then be inspected as specified in section 3, General R@q,nirements, para~aph 3.2.k. 3.7 Frocedure V. Bench handling test. - l’hiaprocedure shall bs used to deter- mine the ability of equipmentto withstand the shock encounteredduring servicing. The chassis and front panel assembly shall be removed from its enclosure, as for serv- icing, and placed in a suitablepositIon for servicing on a horizontal, solid wooden bench top at least l-5/8 inches thick.
The test shall be performed, as follows, in a manner simulatingshocks liable to occur during servicing: . . M@l!ROD516.1 516.1-4 20 October,1969 .. ,:;.-+ ., ,., .. -. ...-. ,.. .,=4 .-: ., ., c