NERLITE Smart Series MAX Illuminator Configuration Guide (EN)

NERLITE Smart Series MAX Illuminators Configuration Guide Hardware Required P/N 83-230016-02 Rev E Continuous Mode Continuous Mode With Dimming Or On-Off Control High Output Strobe Mode Daisy Chain, All Modes PART NUMBER DESCRIPTION Current Draw @ 24VDC (typ.) No Controller Required (Can Be Connected Directly To 24VDC) No Controller Required (Can Be Connected Directly To 24VDC) No Controller Required (Can Be Connected Directly To 24VDC) No Controller Required (Can Be Connected Directly To 24VDC) NER-011660100G MAX 45 Red 10 Degree 75mA Figures A or E Figure B Figure C Not Applicable NER-011660101G MAX 45 Red 50 Degree 75mA Figures A or E Figure B Figure C Not Applicable NER-011660110G MAX 45 White 10 Degree 75mA Figures A or E Figure B Figure C Not Applicable NER-011660111G MAX 45 White 50 Degree 75mA Figures A or E Figure B Figure C Not Applicable NER-011660200G MAX 100 Red 10 Degree 275mA Figures A or E Figure B Figure C Not Applicable NER-011660201G MAX 100 Red 50 Degree 275mA Figures A or E Figure B Figure C Not Applicable NER-011660210G MAX 100 White 10 Degree 275mA Figures A or E Figure B Figure C Not Applicable NER-011660211G MAX 100 White 50 Degree 275mA Figures A or E Figure B Figure C Not Applicable NER-011660300G MAX 300 Red 10 Degree 750mA Figures A or E Figure B Figure C Figure D NER-011660301G MAX 300 Red 50 Degree 750mA Figures A or E Figure B Figure C Figure D NER-011660310G MAX 300 White 10 Degree 750mA Figures A or E Figure B Figure C Figure D NER-011660311G MAX 300 White 50 Degree 750mA Figures A or E Figure B Figure C Figure D Item Description Part Number 1 MAX Series Lights NER-011660XXXG 2 Power Supply DSP100 24VDC 4.2A DIN Mount 97-000006-01 2 Power Supply DSP60 24VDC 2.5A DIN Mount NER-011504100 3 Cable, 5P M12 Female To Flying Leads, 3M 61-000186-01 3 Cable, 5P M12 Female To Flying Leads, 5M 61-000187-01 4 Cable, 5P M12 Male To 5P M12 Female, 1M 61-000184-01 4 Cable, 5P M12 Male To 5P M12 Female, 3M 61-000185-01 5 Cable, Power Smart Series to QX-1 61-000204-01

Стр. 1

NERLITE Smart Series MAX Illuminators Accessories Connections: Control Signals DIM (Continuous Mode With PWM Dimming): DIM (Continuous Mode With On-Off Control): TRIG (High Output Strobe Mode): optoisolated, 0VDC (LEDs off) to 3.1-28.8VDC (LEDs on), 10mA max, 20 µs min Trigger pulse width. Note: High Output Strobe internally limits LED frequency and pulse width to a maximum of 90Hz and 1mS respectively. Light output pulse will follow Trigger pulse width from 20 µs to 1ms. Cable Specifications: Wire colors for flying lead cables: Pin 1 = Brown Pin 2 = White Pin 3 = Blue Pin 4 = Black Pin 5 = Gray Connector Nut = Shield Note: Non-Omron Microscan cables may use different wire colors.

It is the customer’s responsibility to make sure the light is connected correctly per the pin numbers in the table above. Copyright ©2019 Omron Microscan Systems, Inc. www.microscan.com Description Part Number Application AC Power Cord US NER-030028300 Power Cord For Power Supply AC Power Cord EU NER-030028400 Power Cord For Power Supply AC Power Cord UK NER-030028500 Power Cord For Power Supply Input Connector (M12 Male, 5 Circuit, A-Code) Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 Backshell Continuous Mode (Figures A & E): +20.2-28.8VDC DC GND DC GND +20.2-28.8VDC No Connection Shield Continuous Mode With Dimming (Figure B):

+20.2-28.8VDC DC GND DC GND & DIM (-) +20.2-28.8VDC Dim (+) Shield Continuous Mode With On-Off Control (Figure B): +20.2-28.8VDC DC GND DC GND & DIM (-) +20.2-28.8VDC Dim (+) Shield High Out put S tro be Mode (Figure C): +20.2-28.8VDC TRIG (-) DC GND TRIG (+) No Connection Shield Daisy Chain, All Modes, MAX 300 Only (Figure D): Note: The Output (Daisy Chain) Connector (M12 Female, 5 Circuit, A-Code) has an identical pin out to the Input Connector. The Output (Daisy Chain) Connector passes through any signal applied to the Input Connector. Do not attempt to connect more than a total of four lights in a daisy chain confgi uration.

The 24VDC power supply’s maximum current rating must be greater than or equal to the combined total current draw of all lights connected in the daisy chain. imming): on) pulse width modulated (PWM) s ith Dimming, the LED duty cycle will Control): 0VDC (LEDs off), 3.1-3.

Стр. 2