Nucleo GX Manual Go to Settings → Devices → MultiPlus/Quattro/EasySolar. A notification there indicating a new MK3 version is available. Tap the notification and start the update There is a small chance, around 5% based on our data, that this update may briefly restart the system, causing the inverter/ charger to cycle off and on. If no update prompt appears, your system is already up to date. This manual update is only required once and was designed to be user-initiated due to the small restart risk. Future updates will install automatically without causing a restart.
GX Error #60 – Could not connect to the GX device This error occurs when the Marine MFD app fails to establish a connection with the GX device. To resolve the issue, try rebooting the GX device and/or the MFD. 18.2. FAQ 18.2.1. Q1: I cannot switch my Multi/Quattro system on or off To solve the problem, first find out how the system is connected, and then follow the right step by step instruction below. There are two ways to connect a Multi/Quattro system to a Nucleo GX. In most systems they will be connected directly to the VE.Bus port on the back of the NGX. And, option two, in some systems they are connected to the Nucleo GX using a VE.Bus to VE.Can interface .
Step by step instructions when connected to VE.Bus port on the NGX 1. Update the Nucleo GX to the latest available version. See our blog posts in the https://www.victronenergy.com/blog/category/firmware-software/ . 2. Do you have a Digital Multi Control or VE.Bus BMS in the system? In that case it is normal that on/off is disabled. See also the VE.Bus related notes in the NGX manual . 3. In case you have had a Digital Multi Control or VE.Bus BMS connected to your system, the Nucleo GX remembers it and even when those accessories have been removed, the On/Off switch will still be disabled. To clear the memory, execute a Redetect system in the Remote Console menu for your Multi or Quattro.
For details see the Advanced menu section. 4. For parallel/three-phase systems consisting of more than 5 units: depending on temperature and other circumstances, it might not be possible to switch a system back on after switching it off with the NGX. As a work around you'll need to unplug the VE.Bus cable from the back of the NGX. And plug it back in after starting the VE.Bus system. The real resolution is to install the “NGX dongle for large VE.Bus systems”, partnumber BPP900300100. For details, read its connection instruction . Step by step instructions when connected to NGX via VE.Can. 1. Update the Nucleo GX to the latest available version. See our blog posts in the firmware category. 2.
Update the VE.Bus to VE.Can interface to the latest version. The easiest way to do that is by using Remote firmware update: having a special piece of hardware, the CANUSB, is then not necessary. 3. Do you have a Digital Multi Control or VE.Bus BMS in the system? In that case it is normal that on/off is disabled. See also the VE.Bus related notes in the NGX manual 4. In case you have had a Digital Multi Control or VE.Bus BMS connected to your system, and it is now no longer connected, the Canbus interface remembers it. Therefore, even after those accessories have been removed, the On/off switch will still be disabled.
Clearing this memory is unfortunately not possible yourself, please contact us so we can help you. 18.2.2. Q2: Do I need a BMV to see proper battery state of charge? It depends. For details see the Battery state of charge (SoC) chapter. GX devices do not have a built-in 3G or 4G modem, and therefore do not include a SIM card slot. 18.2.3. Q3: I have no internet. Where can I insert a SIM card? To connect to the internet via mobile data, purchase a mobile router with Ethernet ports. These devices handle the SIM card and provide an internet connection to the GX device over Ethernet. 18.2.4. Q4: Can I connect both a GX Device and a VGR2/VER to a Multi/Inverter/Quattro? No, this is not possible.
Page 160 Troubleshooting