Atari Black Widow — Atari Black Widow Arcade Game Operator's Manual PDF

COIN LOCKOUT Descriptions of Black Widow Printed Circuit Board Names Coin Lockout is a game PCB output signal developed from the data on line DB3. When clocked by LATCH, latch R9 of the Coin Door and Control Panel Output circuit latches the data bit on DB3 to pin 9 of R9. From here, the signal is current amplified and inverted by Q2 and applied to the Right and Left Lockout Coils of the game Coin Door. A10, A13-A15 BLANK Address bits on Microprocessor Address Bus lines A10 and A13-A15 are generated by Microprocessor C2. Bits on lines A13-A15, together with those on AB11-AB12, are the input bits to Address Decoders R1-R2.

A10 is exclusive-ORed with BANK SEL by gate B6 to produce the A10 input bit for Random-Access Memory N/P1. Blank is an active high-level signal generated by counter M3 in the Z Intensity and Blanking circuit and ORed with Z BLANK by gate M5 of the R-G-B Output circuit. When high, BLANK turns off transistors Q6, Q8, and Q10, which kills the RED, GREEN, and BLUE output signals to the display. Microprocessor Data Bus lines D0-D7 form a bi-directional data bus between the Microprocessor, the Read-Only Memory, and the Option Switch Input circuits. BLUE DBO-DB7 Blue is a game PCB output signal developed from the data on line DVYO.

When the data bit on DVY0 is high and latch K10 of the Buffered Microprocessor Data Bus lines DBO-DB7 form a buffered bi-directional data bus between microprocessor data-bus buffer F2 and Vector Memory Data Buffer P8; Coin-Door and Control Panel Input circuit buffers L9, M9, and N9; High-Score Table ABO-AB12 Address bits on Buffered Microprocessor Address Bus lines ABO-AB12 are software-generated by Microprocessor C2 and buffered by B1 and C1. These signals are the input bits to Read-Only Memories D1, E/F1, H1, J1, K/L1, and M1; and to Random-Access Memory N/P1. Address bits AB6-AB8 are the select input signals for Address Decoder P3.

Address bits AB11-AB12 anc A13-A15 are the input bits for Address Decoders R1 and R2. Address bits ABO-AB13 are applied with bits from AVGO-AVG12 to Vector Address Selectors K8, M8, L8, and N8 to produce the R-G-B Output circuit is clocked by STATCLK, the data on DVYO is inverted and latched to pin 11 of K10. If both BLANK and Z BLANK are low, this data bit is again inverted by gate L10 to turn on Q10. Transistor Q10 generates the BLUE signal for the display. BUFFEN Buffer Enable is an active low-level signal developed from Bo2 by Vector Address Selector K8. BUFFEN is the enable input signal for Vector Memory Data Buffer P8. When low, BUFFEN allows P8 to pass data. data on lines AMO-AM12.

Bo2 Bits ABO-AB3 are control signals to custom audio chips B3 and C/D3 in the Option Switch Input and Audio Output circuit. Bits ABO-AB5 are the input signals to latch P2 in the High-Score Table circuit where they are used to produce the A1-A5 address input for EAROM M2. The active high-level Phase 2 Clock signal is hardware-generated from the internal clock circuitry of Microprocessor C2, buffered by B1, and applied to AND gate K4. Gate K4 ANDs together Bo2, R/WB, and 3 MHz to produce WRITE. B@2 is also used as the clock signal for custom audio chips B3 and C/D3 of the Option Switch Input and Audio Output circuit.

AB13 Bo2 AB13 is from AB13, inverted by J3, and applied to Vector Ad- The active low-level Phase 2 Clock signal is generated at pin 12 specific Vector Memory Read-Only Memory. of F3 by inverting B¢2. Bd2 is applied to Vector Address Selector K8 to produce BUFFEN. AMO0-AM13 CENTER dress Selector M8. When VMEM is low, AB13 and AB12 select the Address bits on Multiplexed Address Bus lines AMO-AM13 are software-generated by Vector Address Selectors K8, L8, M8, and N8. When VMEM is low, the Multiplexed Address Bus is from Buf- fered Microprocessor Address Bus ABO through AB12 and AB13. When VMEM is high, AMO-AM12 is from Vector-Generator Address Bus lines AVGO-AVG13.

Signals AMO-AM11 are the input address signals to Vector ReadOnly Memories L7, M/N7, N/P7, R7 and to Vector Random-Access Memory K7. In addition, AM11-AM13 are the select input signals for Vector Address Decoder J7. AMO-AM7 are input signals for multiplexers N3 and R3 of the State Machine circuit. AUD 1-AUD 2 The Audio 1 and Audio 2 signals are game PCB output signals that are generated by custom audio chips B3 and C/D3 of the Option Switch Input and Audio Output circuit. AUD 1 is the inverse of AUD 2. These signals are applied to the Audio/Reguiator li PCB and ultimately drive speakers 1 and 2.

AVG0-AVG13 Center_is an active-low level signal software-generated_by gating CNTR with HALT by Center Flag gate L6. When low, CENTER closes switches E10 of the Y-Axis Output circuit and B10 of the X-Axis Output circuit to center the beam on the display. CNTR The active high-level Center Flag signal is software-generated by latch _E5 of the Center Flag circuit. CNTR is set high when VGCK, STROBES, and OP2 are low CNTR is applied to gate J5 of the Normalization Flag circuit to develop the clear signal for latch A6. CNTR is ORed with VCTR by GO Flag gate M5 to generate the GO signal.

CNTR DO-D7 DVY0-DVY12, DVY12 Data bits on Y-Axis Vector Data lines DVYO-DVY12 and DVY12 are software-generated by Vector Data Shifters F8, H8, J8, and by latch D6 of the Op Code and Intensity Latches circuit. DVY3DVY11 and DVY12 are the input signals for digital-to-analog converter (DAC) F9 of the Y-Axis Output circuit. The data carried on these lines represents the Y-axis change from the current location Disable Data is an active_low-level signal generated by test equipment connected to the DIS DAT test point. DIS DAT is ANDed with the ROM signal by gate E3 to produce the enable signal for buffer E2 of the Read-Only Memory circuit.

When enabled, buffer E2 passes data from the selected Read-Only Memory to the Microprocessor Data Bus. DISRST Display Reset is an active low-level signal software-generated by gate L6 of the Halt Flag circuit. When either RESET or VGRST. is low, DISRST is set low When low, DISRST clears State Machine Reference and Bipolar Current lower 512 positions, which means a negative direction of change on the display. If DVY12 is high, DAC F9 operates only in its upper 512 positions for a positive direction of change on the display. In addition, Reference and DVY0O-DVY7 Bipolar are applied to latch E8 in the DAC Current Sources circuit.

These signals, together with VCTR and VCTR, set the X REF and Y REF voltage levels (via DAC D9). DIS DAT P4, DAC In addition, DVX11 and DVX12 are exclusive-ORed by gate B6 of the Normalization Flag circuit. of the display beam. If DVY12 is low, DAC F9 operates only in its latches K2 and J2; and High-Score Table buffer H2. latch lower 512 positions, which means a negative direction of change on the display. If DVX12 is high, DAC A/B9 operates only in its upper 512 positions for a positive direction of change on the display. Sources latch Lines DVYO-DVY2 carry data representing the eight different color signals for latch K10 of the R-G-B Output circuit. .

Lines DVY4-DVY7 carry data representing the Z-intensitySignals for latch E6 of the Z Intensity and Blanking circuit. Data on DVY8-DVY10 are applied to latch D7 of the Vector Scaling circuit. The data carried on these lines represents the number (in binary) that the Vector Scaling circuit uses to divide into the vector drawing time. The vector drawing time n is divided by 2, where n equals the number represented on DVY8-DVY10. In addition, DVY11 and DVY12 are exclusive-ORed by gate B6 of the Normalization Flag circuit. E8, R-G-B Output latch K10, Vector Scaling latch D7, Z Intensity and Blanking latch E6 and counter M3.

In addition, DISRST presets the HALT signal from latch L5 to the high level. EAROMCON The Electrically-Alterable ROM Control signal is an active lowlevel signal software-generated by Address Decoder P3 at address 8900. EAROMCON is the clock signal for latch K2 in the HighScore Table circuit. EAROMCON allows K2 to pass data bits on lines DBO-DB3 to the control lines of EAROM M2. DVG0O-DVG7 Data bits on Vector-Generator Data Bus lines DVGO-DVG7 are software-generated by the selected Vector Read-Only Memory or Vector Random-Access Memory.

If Vector Memory Data Buffer P8 is enabled (BUFFEN is low) and the R/WB line is low, the data on lines DVGO-DVG7 is passed through P8 to the Buffered Microprocessor Data Bus to be read by the microprocessor. Otherwise, the data on DVGO-DVG7 is sent to the Vector Data Shifters and to the Op Code and Intensity Latches. EAROMRD The Electrically-Alterable ROM Read Enable is an active lowlevel signal software-generated by Address Decoder R2 at address 7000. EAROMRD is the read-enable signal for buffer H2 of the High-Score Table circuit. EAROMRD allows the eight data bits from EAROM M2 to be passed through buffer H2 to the microprocessor data bus.

DVX3-DVX12, DVX12 EAROMWR Data bits on X-Axis Vector Data lines DVX3-DVX12 and DVX12 are software-generated by Vector Data Shifters A8, B8, C8, and by The Electrically-Alterable ROM Write Enable is an active lowlevel signal software-generated by Address Decoder P3 at address 8940. EA is the clock signal for latches J2 and P2 in the latch C6 of the Op Code and Intensity Latches circuit. DVX3DVX11 and DVX12 are the input signals to digital-to-analog converter (DAC) A/B9 of the X-Axis Output circuit. The data carried on these lines represents the X-axis change from the current location of the display beam. If DVX12 is low, DAC A/B9 operates only in its High-Score Table circuit.

EAROMWR allows address bits on lines ABO-ABS5 and data bits on lines DBO-DB7 to pass to the address and data input pins of EAROM M2. The active low-level Center Flag signal is software-generated by latch E5 of the Center Flag circuit. When clocked by the 12-MHZ signal, E5 latches STOP to pin 9 to produce CNTR. CNTR is gated with HALT by Center Flag gate L6 to generate CENTER. A. ATARI COIN CNTR-L Address bits on Vector-Generator Address Bus lines AVGOAVG13 are software-generated by Vector Address Controller J9. When VMENM is high, these signals are passed through the Vector Address Selectors on lines AMO-AM13 to the Vector Read-Only Memory and the Vector Random-Access Memory.

Coin Counter Left is a game PCB output signal developed from the data bit on line DB1. When clocked by LATCH, latch R9 of the Coin Door and Control Panel Output circuit latches the data bit on DB1 to pin 6 of R9. From here, the signal is current amplified and inverted by Q4 and applied to the game Utility Panel to activate the Left Coin Counter. BANK SEL COIN CNTR-R The Bank Select signal is developed from data on line DB2. When latch R9 of the Coin Door and Control Panel Output circuit is clocked by LATCH, R9 latches the data on DB2 to pin 2 of R39, producing the BANK SEL signal.

BANK SEL is exclusive-ORed with the address bit A10 by gate B6 to produce input address bit A10 for Random-Access Memory N/P1. Coin Counter Right is a game PCB output signal developed from the data bit on line DBO. When clocked by LATCH, latch R9 of the Coin Door and Control Panel Output circuit latches the data bit on DBO to pin 5 of R9. From here, the signal is current amplified and inverted by Q3 and applied to the game Utility Panel to activate the Right Coin Counter. NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvale, CA.

This drawing is only conditionally issued, and neither receipt nor possession thereof confers or transfers any right in, or license to use, the subject matter of the drawing or any design or technical information shown thereon, nor any right to reproduce this drawing or any part thereok Except for manufacture by vendors of Atari, Inc., and for manufac- ture under the corporation's written license, no right is granted to reproduce this drawing or thé subject matter thereof, unless by written agreement with or written permission from the corporation. Black Widow PCB Signal Name Descriptions © ATARI INC., 1983 © A Warner Communications Company SP-234 Sheet 3B 2nd printing