Atari Black Widow — Atari Black Widow Arcade Game Operator's Manual PDF

Black Widow PCB Signal Name Descriptions, cont. LATCH2 OP1 Latch 2 is an active low-level signal software-generated by decoder H7 of the State Machine circuit. LATCH2 is applied through inverter F7 to the SO input pins of shift registers A8 and C8 in the Vector Data Shifters circuit. LATCH2 causes the data bits on lines DVG0-DVG7 to be latched by A8 and C8 to lines DVX3-DVX7 when A8 is clocked by the 12-MHz clock signal. The Op Code 1 signal is software-generated by latch D6 in the Op Code and Intensity Latches circuit. If the data on line DVG6 is high, OP1 is set high when D6 is clocked by LATCH1.

OP1 is multiplexed with AM5 by N3 in the State Machine circuit to produce the A5 input address bit for State Machine ROM N4. In addition, OP1 is the OP1 signal for Vector Address Controller J9. In the Vector Timer circuit, OP1 is gated by K5 and E3 to enable a 1 to be loaded into the D input pin of Vector Timer P6 (if NORM or SCALE is low). ENORM INVERT Y LATCH3 The active low-level Normalization Flag is software-generated by gate K4 of the Normalization Flag circuit. If OPO is high, SA is high, and the output from gate J5 is high, ENORM is set low when STROBEO goes high. ENORM is applied through gate E7 to the $1 input pins of Vector Data Shifters A8, B8, C8, F8, H8, and J8.

ENORM multiples the rate of change of the X and Y vector data in the Vector Data Shifters (via shift left operations) at the same 2 factor specified by data on lines DVY8-DVY10. The n number is incremented at a 12-MHz rate until either DVX11 or DVY11 changes state, which then sets ENORM to the high level. Invert Y is an active high-level signal developed from the data bit on line DB7. When clocked by LATCH, latch R9 of the Coin Door and Control Panel Output circuit latches DB7 to pin 15 of R9. When high, INVERT Y closes switch E10 through inverter K9 in the Y-Axis Output circuit. This inverts the Y-axis vector instruction to the display.

Latch 3 is an active low-level signal software-generated by decoder H7 of the State Machine circuit. LATCH3 is applied through inverter F7 to the SO input pin of shift register B8 in the Vector Data Shifters circuit. LATCH3 causes the data bits on lines DVGO-DVG3 to be latched by B8 to lines DVX8-DVX11 when B8 is clocked by GO The Go flag is an active high-level signal software-generated by gate M5 of the Go Flag circuit when either VCTR or CNTR are high. GO is gated with HALT* by gate N5 of the State Machine circuit to produce the A7 input address bit for State Machine ROM N4. GO is also used as the enable signal for Vector Timer R6. When GO is high, the Vector Timer starts its count.

The Vector Timer counts to 256 if OP1 is high and OP1 is low If OP1 is low and OP1 is high, the Vector Timer counts to 16K. GREEN Green is a game PCB output signal developed from the data on line DVY1 in the R-G-B Output circuit. When DVY1 is high and latch K10 is clocked by STATCLK, the data bit on DVY1 is inverted and latched to pin 6 of K10. If both BLANK and Z BLANK are low, this data bit is again inverted by gate L10 to turn on Q8. Transistor Q8 generates the GREEN signal for the display. HALT The active high-level Halt Flag is software-generated by latch L5 of the Halt Flag circuit. HALT is applied through buffer M9 of the Coin Door and Control!

Panel Input circuit (when SINP1 is low) to permit Microprocessor C2 to read the status of HALT on line DB6. In addition, HALT is applied to latch P4 of the State Machine cirCuit to develop HALT* lO The Input/Output signal is an active low-level signal softwaregenerated by Address Decoder R2 during addresses 8000 through 8FFF. IO is gated with R/WB by gate J6 to produce the direction signal for bi-directional data buffer N9 of the Coin Door and Con- trol Panel Input circuit. |O determines the direction of data flow through buffer N9. 0s 1/OS is an active high-level signal software-generated from Address Decoder R2 during addresses 6000 through 6FFF.

The 1/OS signal is ORed with the ROM signal by gate R4 to enable bi-directional data bus buffer F2 to pass data. When I/OS is high, data buffer F2 is turned off, which allows custom audio chips B3 and C/D3 to pass data to the data bus. 1/00 I/O0 is an active low-level signal software-generated by Address Decoder R2 at address 6800. |/O0 is the chip-select enable for custom audio chip C/D3 in the Option Switch Input and Audio Output circuit. 1101 1/01 is an active low-level si ignal software-generated by Address Decoder R2 at address 6000. |/O1 is the chip-select enable for custom audio chip B3 in the Option Switch Input and Audio Output Circuit.

LATCH HALT* The active high-level Delayed Halt Flag is software-generated by latch P4 of the State Machine circuit. HALT* is generated when the HALT signal has been delayed by one pulse of inverted VGCK (1.5 MHz), which in turn has been delayed by one pulse of 12 MHz. HALT* is ORed with GO by gate N5 of the State Machine circuit to produce the A7 input address bit for State Machine ROM N4. Latch is an active low-level signal generated by Address Decoder P3 at address 8800. LATCH is the clock signal for latch R9 in the Coin Door and Control Panel Output circuit. When low, LATCH allows the data bits on lines DBO-DB7 to pass through R9.

LATCHO The active low-level Halt Flag is software-generated by latch L5 of the Halt Flag circuit. HALT is the clear signal for Vector Flag latch E5 and Center Flag latch E5. In addition, HALT is ORed with CNTR by gate L6 of the Center Flag circuit to produce CENTER. INTACK LATCH1 Interrupt Acknowledge is an active low-level signal softwaregenerated from Address Decoder P3 at address 88CO. This signal is an acknowledgment from_Microprocessor C2 that an interrupt request has been received. INTACK resets counter J4. Latch 1 is an active low-level signal software-generated by decoder H7 of the State Machine circuit.

LATCH1 is applied through inverter F7 to the SO input pin of shift register H8 in the Vector Data Shifters circuit. LATCH1 causes the data bits on lines DVGODVG3 to be latched by H8 to lines DVY8-DVY10 when H8 is clocked by the 12-MHz clock signal. INVERT X Invert X is an active high-level signal developed from the data bit on line DB6. When clocked by LATCH, latch R9 of the Coin Door and Control Panel Output circuit latches the data bit on DB6 to pin 12 of R9. When high, INVERT X closes switch B10 through inverter KQ in the X-Axis Output circuit. This inverts the X-axis vector instruction to the display.

The Complementary Op Code 1 signal is sofware-generated by latch D6 in the Op Code and Intensity Latches circuit. This signal is opposite in state to OP1. OP1 is the clear signal for Vector Timers N6 and M6. When OP1 goes low, the count from N6 and M6 is stopped, causing a lowered count from the Vector Timer circuit. This low count is used to draw short vectors on the display. OP1 is also gated with the outputs of the Vector Timers by gates L3 and H3 to set STOP to the low level. the 12-MHz clock signal. LATCH3 is also the clock signal for Op Code and Intensity Latch C6. When LATCHS goes low, the data bits on lines DVG4-DVG7 are latched by C6 to lines Z0-Z2, Z1-Z2, DVX12, and DVX12.

NORM The active high-level Normalization Flag is software-generated by latch A6 in the Normalization Flag circuit. If OPO is high, NORM is set high when STROBEO goes high. NORM is gated with SCALE by gate K5 in the Vector Timer circuit to produce the load-enable OP2 The Op Code 2 signal is software-generated by latch D6 in the Op Code and Intensity Latches circuit. If the data on line DVG7 is high, OP2 is set high when D6'is clocked by LATCH1. OP2 is multiplexed with AM6 by N3 in the State Machine circuit to produce the A6 input address bit for State Machine ROM N4. signal-for Vector Timers M6, N6, P6, and Ré6.

If the Vector Timers are enabled, NORM initiates the divide-by-2" operation of the vector drawing time. (The n factor is specified by the data on lines DVY8-DVY 10 to Vector Scaling latch D7.) If OP2, OPO, STROBES, and VGCK are all low, VCTR from Vector Flag latch E5 is set high when E5 is clocked by the 12-MHz clock signal. OPTION 0-OPTION 2 The Option 0, Option 1, and Option 2 signals are hardware-generated by DIP switch P10. They are applied to switch input buffer L9 of the Coin Door and Control Panel Input circuit. When L9 is enabled by SINP2, OPTION 0-OPTION 2 are passed to Buffered Microprocessor Data Bus lines DB5-DB7.

When STROBE1 goes low, if OP2 is low, it is applied through gates B7 and F3 of the Vector Scaling circuit as the load signal for counter C7. This allows the data latched from DVY8-DVY10 by D7 to be loaded into counter C7. When STROBE1 goes high, counter C7 counts down until it reaches the minimum count. At the same OPO time, the Vector Timer circuit does a divide-by-2 (shift right) opera- tion for each count of C7. (This is caused by SCALE being at the The Op Code 0 signal is software-generated by latch D6 in the Op Code and Intensity Latches circuit. If the data on line DVG5 is high, OPO is set high when D6 is clocked by LATCH1.

OPO is multiplexed with AM4 by N3 in the State Machine circuit to produce the A4 input address bit for State Machine ROM N4. high C7 reaches its minimum count, it sets pin 12 If OP2 and DVY12 are low, SCALELD from gate J6 is set low when STROBE2 goes low This allows Vector Scaling latch D7 to latch the new data on DVY8-DVY10. If OPO is high,ns HALT from Halt Flag latch L5 is set nigh when L5 is clocked by STROBES. If OP2 and DVY12 are low, STATCLK from J6 is set low when STROBE2 goes low This allows latch E6 of the Z Intensity and Blanking circuit to latch the data on DVY4-DVY7.

If OPO, OP2, STROBES, and VGCK are all low, VCTR from Vector Flag latch E5 is set high when E5 is clocked by the 12-MHz clock signal. OP2 OPO The Complementary Op Code 2 signal is software-generated by latch D6 in the Op Code and Intensity Latches circuit. This signal The Complementary Op Code 0 signal is software-generated by latch D6 in the Op Code and Intensity Latches circuit. This signal is opposite in state to OP2. If OP2, STROBE3, and VGCK are low, CNTR from Center Flag latch E5 is set high when E5 is clocked by the 12-MHz clock signal. OP2 is also ORed with SA by gate R4to tion Flag latch A6 is set high when STROBEO clocks A6.

OPO is also the OPO and OPX input signal for Vector Address Controller J9. produce the OP2 input for Vector Address Controller J9. A, ATARI NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvale, CA. This drawing is only conditionally issued, and neither receipt nor possession thereof confers or transfers any right in, or license to use, the subject matter of the drawing or any design or technical information shown thereon, nor any right to reproduce this drawing or any part thereof.

Except for manufacture by vendors of Atari, Inc., and for manufacture under the corporation’s written license, no right is granted to reproduce this drawing or the subject matter thereof, unless by written agreement with or written permission from the corporation. Black Widow PCB Signal Name Descriptions LATCH1 is also the clear signal for Vector Data Shifters A8, B8, C8, F8, J8, and for Op Code and Intensity Latch C6. In addition, LATCH1 is the clock signal for Op Code and Intensity Latch D6. When LATCH1 goes low, the data bitson lines DVG4DVG7 are latched by D6 to lines OPO-OP2, OP0-OP2, DVY12, and DVY 12. state.) When high, dropping SCALE to the low state. is opposite in state to OPO.

IfOPO is low, NORM from NormalizaLatch 0 is an active low-level signal software-generated by decoder H7 of the State Machine circuit. LATCHO is applied through inverter F7 to the SO input pins of shift registers F8 and J8 in the Vector Data Shifters circuit. LATCHO causes the data bits on lines DVG0-DVG7 to be latched by F8 and J8 to lines DVYO-DVY7 when F8 and J8 are clocked by the 12-MHz clock signal. — HALT OP1 © ATARI INC., 1983 © A Warner Communications Company SP-234 Sheet 4A 2nd printing -