SA STATCLK The active low-level Signature Analysis Flag is hardware-generated when test point SA at pin 13 of J3 is grounded. SA is used to place the game PCB in the mode to generate signatures for reading by a Signature Analyzer or the ATARI CAT Box. Black Widow PCB Signal Name Descriptions, cont. SACLK The Player 1 LED On signal is developed from the data bit on line DB4. When clocked by LATCH, latch R9 of the Coin Door and Control Panel Output circuit latches the data bit on line DB4 to pin 19 of R9. This signal is applied through R103 to light the Player 1 LED on the game Control Panel.
Read-Only Memory Chip Select 0 is an active low-level signal software-generated by Address Decoder R1 at addresses 9000-9FFF. ROMO is the chip-select signal for ROM D1 of the Read-Only Memory circuit. When low, ROMO allows ROM D1 to be addressed and to pass data to buffer E2. PLAYER 2 LED ROM1 The Player 2 LED On signal is developed from the data bit on line DB5. When clocked by LATCH, latch R9 of the Coin Door and Control Panel Output circuit latches the data bit on DB5 to pin 16 of R9. This signal is applied through R102 to light the Player 2 LED on the game Control Panel.
Read-Only Memory Chip Select 1 is an active low-level signal software-generated by Address Decoder R1 at addresses A000-AFFF. ROM1 is the chip-select signal for ROM E/F1 of the Read-Only Memory circuit. When low, ROM1 allows ROM E/F1 to be addressed and to pass data to buffer E2. POR ROM2 The active high-level Power-On Reset signal is hardware-generated at pin 4 of F7 in the Power-On Reset circuit. POR is the clock signal that starts the count of E4 of the Clock circuit. Read-Only Memory Chip Select 2 is an active low-level signal software-generated by Address Decoder R1 at addresses BO00-BFFF. ROM2 is the chip-select signal for ROM H1 of the Read-Only Memory circuit.
When low, ROM2 allows ROM H1 to be addressed and to pass data to buffer E2. POR The active low-level Power-On Reset signal is hardware-generated at pin 6 of inverter F7 in the Power-On Reset circuit. POR is ROM3 or when the RESET test point is shorted to ground. POR is developed into the RESET signal to protect Microprocessor C2. Read-Only Memory Chip Select 3 is an active low-level signal software-generated by Address Decoder R1 at addresses C000-CFFF. ROMS is the chip-select_signal for ROM J1 of the RAM addressed and to pass data to buffer E2. generated when the voltage at pin 3 of R8 is less than about 7 volts Read-Only Memory circuit.
When The Random-Access Memory Enable is an active low-level signal software-generated by Address Decoder R2 during addresses 0000 through 07FF. RAM is the chip-enable signal for RandomAccess Memory N/P1. When low, RAM allows data to be read from or written to N/P1, depending upon the state of WRITE. RED Red is a game PCB output signal developed from the data on line DVY2 in the R-G-B Output circuit. When DVY2 is high and latch K10 is clocked by STATCLK, the data bit on DVY2 is inverted and latched to pin 3 of K10. If both BLANK and Z BLANK are low, this data bit is again inverted by gate L10 to turn on Q6. Transistor Q6 generates the RED signal for the display.
low, ROM3 allows ROM J1 to be ROM4 Read-Only Memory Chip Select 4 is an active low-level signal software-generated by Address Decoder R1 at addresses DO00-DFFF. ROM4 is the chip-select signal for ROM K/L1 of the Read-Only Memory circuit. When low, ROM4 allows ROM K/L1 to be addressed and to pass data to buffer E2. ROM5 Read-Only Memory Chip Select 5 is an active low-level signal software-generated by Address Decoder R1 at addresses EQ00-EFFF. ROMS is the chip-select signal for ROM M1 of the Read-Only Memory circuit. When low, ROM5 allows ROM M1 to be addressed and to pass data to buffer E2.
RESET Reset is an active low-level signal generated at pin 6 of K3 from either the Watchdog circuit or the Power-On Reset circuit. The Power-On Reset circuit sets RESET to an active low level either when the RESET test point is shorted to ground or during the time that the power-supply voltages are reaching their stabilized, regu-lated levels. This ensures that the Microprocessor Address Bus is stabilized before the microprocessor begins operation.
The Watchdog circuit sets RESET to an active low level if the microprocessor fails to output address ODOO before Watchdog The Buffered Read/Write Enable is generated by Microprocessor C2, buffered by B1, and applied as the read/write enable signal for custom audio chips B3 and C/D3 of the Option Switch Input and Audio Output circuit. In the high state, R/WB is the read enable for the custom audio chips; in the low state, it is the write enable for these chips. RESET is also the clear signal for latch R9 in the Coin Door and Control Panel Output circuit. In addition, RESET is gated with VGRST by gate L6 in the Halt Flag circuit to produce DISRST.
ROM The Read-Only Memory Enable is an active high-level signal software-generated from Address Decoder R1 during addresses 9000 through 9FFF. ROM is ORed with I/OS by gate R4 to enable bi-directional data bus buffer F2 to pass data. In addition, ROM is ANDed with DIS DAT to enable data buffer all low, STATCLK is set low Strobe 0 is an active low-level Signal software-generated by State Machine decoder H7. STROBEO is the clock signal for Normalization Flag latch A6. It is also the STROBEO input for Vector Address Controller J9. STROBE1 Scale is an active high-level signal generated by gate B7 of the Vector Scaling circuit. When OP2 is high and counter C7 is counting down, SCALE is set high.
SCALE is ORed with NORM by gate KS of the Vector Timer circuit to produce the load signal for Vector Timers M6, N6, P6, and R6. When SCALE is high, the Vector Timers perform a load operation for each count of C7 (at a 12-NHz rate). This results in a vector drawing time divided by a factor of 2" where n equals the total counts of C7. When C7 reaches its minimum count, SCALE is set low. Strobe 1 is an active low-level signal software-generated by State Machine decoder H7. If OP2 is low, when STROBE1 goes low, the data latched at the outputs of D7 in the Vector Scaling cir- cuit are loaded into counter C7. When STROBE1 goes high, C7 begins counting down. STROBE1 is the STROBE1 J9.
SCALE is gated with VCTR, CNTR, DVY11-DVY12, and DVX11DVX12 of the Normalization Flag circuit to produce the clear Signal for latch A6. input for Vector Address Controller STROBE2 Strobe 2 is an active low-level signal software-generated by State Machine decoder H7. If OP2 and DVY12 are both low, SCALELD from gate J6 is set low when STROBE2 goes low If OP2 and DVY 12 are both low, STATCLK is set low when STROBE2 goes low SCALELD Scale Load is an active low-level signal software-generated by gates N5, L3, and L6 of the Vector Generator circuit. When TROBE2, OP2, and DVY12 are all low, SCALELD is set low SCALELD is the clock signal for Vector Scaling latch D7.
When )CALELD goes high, the data on lines DVY8-DVY10 are latched to the output pins of D7. J9. SINP1 Strobe 3 is an active low-level signal software-generated by State Machine decoder H7. STROBES is the clock signal for Halt Flag latch L5 and is the STROBES input for Vector Address Con: troller J9. STROBE2 is the STROBE2 input for Vector Address Controller STROBE3 Switch Input 1 is an active low-level signal software-generated by Address Decoder R2 at address 7800. SINP1 is the direction signal for bi-directional data buffer M9 of the Coin Door and Control Panel Input circuit and determines the direction of data flow through buffer M9.
If OPO, OP2, OP2, and VGCK are all low, VCTR from Vector Flag latch ES and CNTR from Center Flag latch E5 are both set high when STROBE3 goes low STO-ST2 State signals STO-ST2 are active high-level signals that are software-generated by State Machine ROM N4. These signals, together with ST3, are decoded by H7 of the State Machine circuit to produce LATCHO-LATCH3 and STROBEO-STROBE3. ST2 is used to veveioP ST3 and is also the ST2 input for Vector Address Controller J9. Switch Input 2 is an active low-level signal software-generated by Address Decoder R2 at address 8000.
SINP2 is the direction signal for bi-directional data buffer L9 of the Coin Door and Con- trol Panel Input circuit and determines the direction of data flow through buffer L9. MATARI M, al- lows data to pass through P8 from the data bus to the vector generator data bus; in the low state, it allows data to pass in the reverse direction. NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvale, CA.
This drawing is only conditionally issued, and neither receipt nor possession thereof confers or transfers any right in, or license to use, the subject matter of the drawing or any design or technical information shown thereon, nor any right to reproduce this drawing or any part thereof. Except for manufacture by vendors of Atari, Inc., and for manufac- ture under the corporation's written license, no right is granted to reproduce this drawing or the subject matter thereof, unless by written agreement with or written permission from the corporation. SA The active high-level Signature Analysis Flag signal is hardware-generated at pin 12 of inverter J3 when test point SA at pin 13 is grounded.
SA is used to place the game PCB in the mode to generate signatures for reading by a Signature Analyzer or the ATARI CAT Box. are STROBEO SCALE the Microprocessor circuit by inverting R/WB. R/WB is ANDed with Bd2 and 3 MHz by gate K4 to produce WRITE. R/WB is the direction signal for Vector Memory Data Buffer P8 and determines P8. In the high state, R/WB DVY12 P6, and R6 have reached their maximum count. If STOP is low, VCTR from Vector Flag latch E5 and CNTR from Center Flag latch ES are both set low when E5 is clocked by the 12-MHz clock Signal. Signature Analysis Enable is a test point at pin 8 of gate M65 in the Vector Address Selector circuit.
SAEN is generated by gating VRAM with the data bit on line AM10 by gates J3 and M5. SAEN is used to enable a Signature Analyzer or the ATARI CAT Box for the reading of game PCB signatures. The Buffered Read/Write Eanble is generated at pin 2 of F3 in the direction of data flow through and Stop is an active low-level signal generated by gate H3 of the SAEN R/WB counter H4 has reached its maximum count. OP2, Vector Timer circuit. STOP is set low when Vector Timers N6, M6, SINP2 R/WB STROBE2, STATCLK is the clock for latch K10 in the R-G-B Output circuit and latch E6 in the Z Intensity and Blanking circuit.
When STATCLK goes high, the data bits on DVYO-DVY2 are latched by K10, and those on DVY4-DVY7 are latched by E6. STOP ” ROMO CNicp PLAYER 1 LED Signature Analysis Clock is a test point at pin 8 of gate B7 in the State Machine Clock Logic circuit. SACLK is used to apply the clock signal from the Signature Analyzer or ATARI CAT Box for the reading of game PCB signatures. State Clock is an active low-level signal software-generated by gates N5, L3, and J6 of the Vector Generator circuit. When Black Widow PCB Signal Name Descriptions © ATARI © INC., 1983 A Warner Communications Company SP-234 Sheet 4B 2nd printing