Atari Black Widow — Atari Black Widow Arcade Game Operator's Manual PDF

Z Intensity and Blanking circuit to produce the select signal for latch F6. This select signal causes the latched data from E6 to be applied as the input signals for latch F6. X OUT X Output is a game PCB output signal generated by the X-Axis Output circuit. X OUT carries the horizontal beam deflection signal for the drawing of vectors on the display. Black Widow PCB Signal Name Descriptions, cont. Z OUT Z Intensity Output is a game PCB output signal generated by the Z Intensity and Blanking circuit from either DVY4-DVY7 or Z0-Z2. The Q output signals from latch H6 are summed at the base of Q7.

Transistors Q7 and Q9 buffer Z OUT before it is sent to the game display circuitry to control the display intensity. X REF The X-Axis Voltage Reference is set by the DAC Reference and Bipolar Current Sources circuit. This is the reference voltage applied to pin 14 of X-axis digital-to-analog converter (DAC) A/B9 of the X-Axis Output circuit. 3 KHZ Y BIP ST3 VROMO State signal ST3 is an active high-level signal hardware-generated by Decoder Disable latch A7. ST3 is opposite in state to VGCK, and is delayed by one pulse of the 12-MHz clock signal if the Q4 output from State Machine ROM N4 is low and VMEM is high. If the Q4 output from N4 is high, ST3 is high.

When ST3 is high, State Machine decoder H7 is disabled. When ST3 is low, H7 decodes the data on lines STO-ST2 to produce LATCHO-LATCH3 and STROBEO-STROBE3. Vector Read-Only Memory Chip Select 0 is an active low-level signal software-generated by Vector Address Decoder J7 at addresses 2800-2F FF. VROMO is the chip-select signal for ROM L7 of the Vector Read-Only Memory circuit. When low, VROMO allows ROM L7 to be addressed and to pass data to the Vector Generator Data Bus. VCTR, VCTR The Vector Flag signals are software-generated by Vector Flag latch E5. If OPO, OP2, STROBE3, and VGCK are low and HALT is high, VCTR is set high and VCTR is set low when E5 is clocked by the 12-MHz clock signal.

VCTR is ORed with CNTR by gate M5 to set GO high. SCALE, CNTR, DVY11-DVY12, and DVX11-DVX12 are gated with VCTR to produce the clear signal for Nomalization Flag latch A6. In the Z Intensity and Blanking circuit, VCTR is the clock signal for latch H6 and the serial input signal for shift register M3. VCTR and VCTR are used by the DAC Reference and Bipolar Current Sources circuit to set the X BIP, Y BIP, X REF, and Y REF levels. VROM1 Vector Read-Only Memory Chip Select 1 is an active low-level signal software-generated by Vector Address Decoder J7 at addresses 3000-3FFF. VROM1 is the chip-select signal for ROM M/N7 of the Vector Read-Only Memory circuit.

When low, VROM1 allows ROM M/N7 to be addressed and to pass data to the Vector Generator Data Bus. VROM2 Vector Read-Only Memory Chip Select 2 is an active low-level signal software-generated by Vector Address Decoder J7 at addresses 4000-4FFF. VROM2 is the chip-select signal for ROM N/P7 of the Vector Read-Only Memory circuit. When low, VROM2 allows ROM N/P7 to be addressed and to pass data to the Vector Generator Data Bus. VROM3 VGCK The Vector Generator clock signal is generated at pin 18 of buffer B1 in the Microprocessor circuit. VGCK is derived from the 1.5 MHz clock signal and is applied to AND gate J5 of the State Machine Clock Logic circuit.

VGCK is the basic timing signal of the State Machine circuit. Vector Read-Only Memory Chip Select 3 is an active low-level signal software-generated by Vector Address Decoder J7 at addresses 5000-5F FF. VROMS is the chip-select signal for ROM R7 of the Vector Read-Only Memory circuit. When low, VROM3 allows ROM R7 to be addressed and to pass data to the Vector Generator Data Bus. VGGO VW The Vector Generator Go signal is an active low-level signal software-generated by Address Decoder P3 at address 8840. VGGO is the clear signal for latch L5 of the Halt Flag circuit. When low, VGGO sets HALT to the inactive low level.

generated from Vector Address Selector K8, ANDed with B¢2 by The Y-Axis Bipolar Current is set by R98 of the DAC Reference and Bipolar Current Sources circuit. This is the current source for pin 18 of Y-axis digital-to-analog converter (DAC) F9 of the Y-Axis Output circuit. The 3 kHz clock signal is generated at pin 6 of Clock counter F4 and is applied through switch input buffer M9 of the Coin Door and Control Panel Input circuit (when SINP1 is low). The 3 kHz clock is read by the microprocessor on data line DB7. This frequency is the time reference for the Microprocessor C2. Y OUT 12 KHZ Y Output is a game PCB output signal generated by the Y-Axis Output circuit.

Y OUT carries the vertical beam deflection signal for the drawing of vectors on the display. The 12 kHz clock signal is generated at pin 4 of Clock counter F4 and is applied to reset A4 of the High-Score Table. 3 MHZ The 3 MHz clock signal is generated at pin 2 of Clock counter F4. The 3 MHz signal is ANDed with R/WB and B@2 by gate K4 to produce WRITE. It is also applied to AND gate J5 of the State Machine Clock Logic and to shift register M3 of the Z Intensity and Blanking circuit. Y REF The Y-Axis Voltage Reference is set by the DAC Reference and Bipolar Current Sources circuit.

This is the reference voltage applied to pin 14 of Y-axis digital-to-analog converter (DAC) F9 of the Y-Axis Output circuit. 6 MHZ Z0-Z2, Z1-Z2 The 6 MHz clock signal is generated at pin 3 of Clock counter F4 and is applied to gate J5 of the State Machine Clock Logic cirCuit. Z Intensity signals ZO-Z2 and Z1-Z2 are software-generated by latch C6 in the Op Code and Intensity Latches circuit. These signals are derived from the data on lines DVG51-DVG7 when C6 is clocked by LATCHS. If the binary count carried by Z0-Z2 is not equal to 1, these signals are the input signals for latch F6 in the Z Intensity and Blanking circuit.

If the binary count carried by 20-22 is 1, Z Intensity signals ZO, Z1, and Z2 are ANDed by gate F5 of the 12 MHZ The 12 MHz clock signal is generated at pin 10 of inverter F3 in the Clock circuit. This signal clocks the Vector Timer Shifters, the Vector Flag latch, and the Center Flag latch. The Vector Write Enable is an active low-level signal softwaregate J6, and applied as the write-enable signal for Vector RandomAccess Memory K7. When low, VW allows data to be written to K7; when high, VW permits data to be read from K7. VGRST Vector Generator Reset is an active low-level signal softwaregenerated by Address Decoder P3 at address 8880.

VGRST is ORed with RESET by gate L6 of the Halt Flag circuit to produce DISRST. Watchdog Clear is an active low-level signal software-generated by Address Decoder P3 at address 8980. WDCLR is ORed with POR by gate E3 to clear the count of Watchdog counter H4. WDDIS VMEM The Vector Memory Select Enable is an active low-level signal software-generated by Address Decoder R1 during addresses 2000 through 5FFF. VMEM is the select-enable signal for Vector Address Selectors K8, L8, M8, and N8. When low, VMEM allows the Vector Address WDCLR Selectors to produce VW, BUFFEN, and the AMO0-AM 12 multiplexed address bits.

VMEM is also applied to gate K5 of the State Machine Clock Logic circuit where it is used to generate ST3. VRAM The Vector Random-Access Memory Chip Enable is.an active low-level signal software-generated by Vector Address Decoder J7 at addresses 2000-27FF. When low, VRAM enables Vector Random-Access Memory K7 to be addressed_to either receive or transmit data, depending upon the state of VW. VRAM is also used to produce the SAEN signal from M5 of the Vector Address Selector circuit. A, ATARI Watchdog Disable is a test point at pin 9 of AND gate L4 in the Watchdog circuit.

When WDDIS is grounded, RESET is prevented from going to an active low level (except when the RESET test point is grounded). WRITE Write Enable is an active low-level signal generated by gate K4 of the Microprocessor circuit. WRITE is used to enable Address Decoder P3 and Random-Access Memory N/P1. WRITE is also ap- NOTICE TO ALL PERSONS RECEIVING THIS DRAWING CONFIDENTIAL: Reproduction forbidden without the specific written permission of Atari, Inc., Sunnyvale, CA.

This drawing is only conditionally issued, and neither receipt nor possession thereof confers or transfers any right in, or license to use, the subject matter of the drawing or any design or technical information shown thereon, nor any right to reproduce this drawing or any part thereof. Except for manufacture by vendors of Atari, Inc., and for manufac- ture under the corporation's written license, no right is granted to reproduce this drawing or the subject matter thereof, unless by written agreement with or written permission from the corporation. plied to pin 11 of K8 in the Vector Address Selector circuit to develop VW.

Black Widow X BIP The X-Axis Bipolar Current is set by R99 of the DAC Reference and Bipolar Current Sources circ,,it. This is the current source for pin 18 of X-axis digital-to-analog converter (DAC) A/B9 of the X-Axis Output circuit. © ATARI INC., 1983 © A Warner Communications Company PCB Signal Name Descriptions SP-234 Sheet 5A 2nd printing