Phoenix Axial Air Mover Manual (EN)

4201 Lien Rd • Madison, WI 53704 Owner’s Manual — Phoenix Axial Air Mover Installation, Operation & Service Instructions Read and Save These Instructions The Phoenix Axial Air Mover is the industry’s only Air Mover specifically engineered with patent pending FOCUS TM Technology. FOCUS TM Technology revolutionizes evaporative drying by producing air velocities greater than competitive product offerings. This highly focused air flow is directed towards the restoration industry’s problematic drying areas namely, carpet and pad, sub-floor, sill plate and walls. No other fan dries the sill plate as quickly!

Finally, the Phoenix Axial Air Mover with FOCUS TM Technology sustains these air velocities further than any other Axial Air Mover. The Phoenix Axial Air Mover includes a 2-speed motor delivering a focused airstream of approximately 3000 cfm, lightweight stackable enclosure designed to fit existing vehicle rigging, on-board duplex GFCI outlet, circuit breaker, superior cord management and hour meter. Conventional air movers create a circular air jet. With a circular air jet the only way to get air into the square corner is to point the fan towards the corner. This angle toward the wall wastes valuable air velocity and throw distance.

FOCUS TM Technology creates an air jet with a square corner, resulting in optimized drying ability. In addition, the Axial Air Mover features built in 4.5° positioning which increases the fans ability to dry. Dry fast, smart and profitably with Phoenix. Patent: 7,331,759 Phoenix Axial Air Mover • Approximately 3000 CFM air flow directed where you need it. • Operator interface conveniently located for easy access, featuring: power indicator lamp, large three- position switch, circuit breaker, GFCI outlet, and hour meter. • Daisy-chain up to four Phoenix Axial Air Movers on a single circuit. • Integral circuit breaker eliminates nuisance trips to the breaker box.

• Axial Air Mover itself is also GFCI protected. • Units interlock for ease of stacking during storage and handling. • Weighs 2.5 lbs less than competitive units. • Linear low density polyethylene construction. • Low bearing temperatures increase motor life. Phoenix Axial Air Mover PN 4025200 TS-285b Specifications subject to change without notice. 05/14 1 www.UsePhoenix.com • sales@UsePhoenix.com Toll-Free 1-800-533-7533

Стр. 1

Table of Contents Introduction ................................................................1 FOCUS TM Technology Features and Benefits .....................1 1. Safety Information .................................................2 2. Intended Application ...............................................3 3. Safety Certifications ...............................................3 4. Specifications ........................................................3 5.

Power Requirements ..............................................3 5.1 Daisy-Chaining.................................................3 5.2 Recommended Use..........................................3 5.3 Integrated Cord Wrap.......................................4 6. Applications ...........................................................4 6.2 Placement.......................................................4 6.3 Orientation of Directional Drying........................4 7. Operating Instructions ............................................5 8.

Operator Panel Features .........................................5 8.1 Run-Time Hour Meter.......................................5 8.2 12 Amp Circuit Breaker....................................5 8.3 Power Indication Lamp.....................................6 8.4 3-Position Drying Selector Switch......................6 8.5 GFCI Protection................................................6 9. Maintenance ..........................................................6 9.1 Servicing.........................................................6 9.2 Cleaning..........................................................6 10. Replacement Parts and Optional Accessories ...........7 11.

Wiring Diagram ......................................................7 12. Warranty ...............................................................9 1 Safety Information • Do not operate the unit with a cut or frayed power cord. Replace cord if it becomes damaged. • Do not unplug the unit by pulling on the cord. Grasp the plug firmly and pull it out of the wall socket or power receptacle. • Always use a grounded outlet. • Never operate electrical equipment in standing water. • Never operate with the safety grills removed. Personal injury may result. • Do not stick your fingers or other objects through the safety grills. • Do not restrict airflow to the unit.

This may cause the unit to overheat. • Unit should never be serviced or cleaned while it is plugged in. • Do not plug more than 9.0 amps total into the GFCI outlet. • Do not sit or stand on the unit or use as a shelf or table. • Check GFCI protection before each use by pushing “test” button. If operating properly, “reset” button will pop out. • Before leaving an Axial Air Mover unattended, ensure children do not have access to the equipment. Do not allow children to play with or near the unit or in its air flow. • To reduce the risk of fire or electric shock, do not use this air mover with any solid-state speed control device. • Do not route cord under furniture or appliances. Serial No.

___________________________ LIRE ET CONSERVER CES INSTRUCTIONS Purchase Date ______/______/_____ • Risque de choc йlectrique Peut causer des blessures ou la mort. Dйbrancher toutes les alimentations en courant йlectrique а distance avant l’entretien ou le nettoyage. • Ne pas utiliser l’appareil avec un cordon d’alimentation coupй ou effilochй. • Ne pas dйbrancher l’appareil en tirant sur le cordon. Tenir la fiche fermement et la tirer hors de la prise murale ou la prise d’alimentation йlectrique. • Toujours utiliser une prise mise а la terre. • Ne jamais utiliser l’йquipement йlectrique dans de l’eau stagnante. • Ne jamais utiliser sans les grilles de protection.

Des blessures risquent d’en rйsulter. • Ne pas passer les doigts ou d’autres objets dans les grilles de protection. • Ne pas diminuer le dйbit d’air arrivant jusqu’а l’appareil. L’appareil risque de trop chauffer. • Ne pas brancher plus de 9 ampиres au total au diffйrentiel. • Ne pas s’asseoir ou se tenir debout sur l’appareil; ne pas l’utiliser comme йtagиre ou table. Dealer’s Name ___________________________________ 2 www.UsePhoenix.com • sales@UsePhoenix.com Toll-Free 1-800-533-7533

Стр. 2

• Vйrifier la protection du diffйrentiel avant chaque utilisation en appuyant sur le bouton “ test “. Si l’appareil fonctionne correctement, le bouton “ reset “ ressort. • Avant de laisser un appareil aйraulique axial sans surveillance, s’assurer que les enfants n’ont pas accиs а l’йquipement. Ne pas laisser les enfants jouer avec l’appareil ou а proximitй de l’appareil ou dans l’air qu’il projette. • Pour rйduire le risque d’incendie ou de choc йlectrique, ne pas utiliser ce ventilateur avec un dispositif de commande de vitesse а semi-conducteurs. 5 Power Requirements 5.1 Daisy Chaining The Phoenix Axial Air Mover draws 2.5 amps.

The 12 amp, on-board circuit breaker will allow four (4) Phoenix Axial Air Movers on one circuit. When daisy-chaining the Phoenix Axial Air Mover, turn on one Phoenix Axial Air Mover at a time to prevent excessive current inrush caused by four units starting at once. A ground fault in the Phoenix Axial Air Mover or anywhere on the circuit will cause the Axial Air Mover’S GFCI to trip. After rectifying the ground fault, reset the GFCI by pressing the reset button. 2 Intended Application The Phoenix Axial Air Mover has changed the drying industry by minimizing overall drying time on water restoration jobs.

The Phoenix Axial Air Mover uses patent pending FOCUS Technology to maximize air velocity across floors and along walls for longer distances. By maximizing the air velocity, water evaporates more quickly from the carpet, pad, sub-floor, wall, and sill plate. 5 3 Safety Certifications The Phoenix Axial Air Mover (P/N 4025200) conforms to UL STD 507. Certified to CAN/CSA STD C22.2 No. 113. Figure 1: Too many Axial Air Movers daisy-chained 4 Specifications Part No. 4025200 5.2 Recommended Use Recommended use(s) of on-board duplex GFCI are shown. Note: Standard 115 VAC electrical outlets. Power 1/4 hp 1-phase 110/120 VAC 2-speed 4-pole, PSC Electric Motor.

CFM Approximately 3000 Cord 20 ft Power Cord 15 Amp Outlet 15 Amp Outlet 15 Amp Outlet Outlet 15A UL Rated GFCI Duplex Receptacle Current Draw 2.5 Amps Voltage 115 VAC Warranty Year One - 100% parts and labor (all components) Year Two - 100% parts only (all components) Years Three through Seven - Only materials and workmanship of the housing are covered. Dimensions Cabinet Width 19.9” Height 19.5” Phoenix 200 MAX Depth 15.2” Weight 29.5 Lbs Figure 2: Duplex GFCI use Phoenix Mini-Guardian 3 www.UsePhoenix.com • sales@UsePhoenix.com Toll-Free 1-800-533-7533

Стр. 3

5.3 Integrated Cord Wrap The Phoenix Axial Air Mover features integrated cord management. Wrap the cord around the cord wrap as shown and secure the cord with the clasp on the plug. the FOCUS Technology corner. The Axial Air Mover sustains this air flow for more than 20 feet and maximizes the air velocity across the floor and along the wall when placed the at 4.5° angle from the wall. By touching the front edge of the output side of the axial air mover against the wall and rotating the rest of the unit against the wall, the restoration professional will place the axial air mover at 4.5° due to the housing’s built-in design.

Industry experts agree placing Axial Air Movers 45° angle to the wall wastes air flow and reduces the performance by forcing air up the wall. The best set up angle for quickly and completely drying the sill plate is 4.5°. Set-up angles greater than 4.5° may be used under unique circumstances such as corner air flow and structure variations. Set-up angle should never exceed 23°. Figure 5: 4.5° to wall as shown Figure 3: Cord wrap 6 Applications 6.1 Sizing for Water Restoration Jobs Current industry standards call for one air mover per 10-16 linear feet of wall space, dependent upon the Class of wa­ ter damage.

For commercial structures, the industry stan­ dard calls for one air mover for every 50-60 square feet. The water restoration industry based these estimates on the air mover technology available when writing the stan­ dards. Following these equipment-sizing standards when using the Phoenix Axial Air Mover will result in dramatically faster drying times. If the restoration professional desires to merely achieve industry standard drying times, he can use fewer Phoenix Axial Air Movers than standard equip­ ment standards allow. 6.3 Orienting of Directional Drying System The axial air mover dries in counter-clockwise and clockwise directions for optimum ease of use.

The axial air mover ships with rubber feet on one side of the unit for counter-clockwise drying. When the water restoration professional needs to employ clockwise drying (such as the need to dry a door jamb), simply rotate the axial air mover 90° so the FOCUS Technology corner points toward the door jamb and floor for the clockwise drying. 6.2 Placement Current industry guidelines suggest placing air movers at a 15° - 45° angle to wall. These guidelines apply to air movers without FOCUS Technology. FOCUS Technology allows the restoration professional to place the Phoenix Axial Air Mover at an angle nearly parallel to the wall.

The test graph shown below depicts immediate air flow at 2500 Air Velocity (fpm) 2000 1500 1000 500 0 0 Feet 5 10 15 20 25 Figure 6: Placement for counter-clockwise drying Figure 4: Airflow of the Phoenix Axial Air Mover measured 3.5” parallel to wall. 4 www.UsePhoenix.com • sales@UsePhoenix.com Toll-Free 1-800-533-7533 Im air flow Im mediate h igh velocity air flow at the ou tlet of the fan.

Стр. 4