••• ROLAND TD-7T TURBO FACTS ••• The TD-7T Turbo Version Percussion Sound Module features over 500 16-bit quality sounds and digital effects. • Assigning Sounds/Layering (cont.) To assign LAYER modes and sounds: The Stage Set includes the revolutionary FD-7 Hi Hat Control Pedal that responds just like an acoustic hi hat, the KD-7 Kick Pedal, 4 PD-7, and 4 PD-9 dual trigger pads. These kits respond to such techniques as press rolls, rim shots and cymbal chokes. 1) Select your desired patch using the DATA dial. 2) From the Patch Page, press EDIT. 3) Cursor to PATCH using the buttons and press ENTER. 4) Cursor to NOTE and press ENTER.
5) Strike the pad or rim that will trigger the sound you wish to edit. 6) Cursor to the Instrument Number and select your Instrument for SOUND 1 with the DATA dial. 7) Push CURSOR LEFT ( SOUND 2 with the DATA dial. 8) Cursor to the Instrument Number and select your Instrument for SOUND 2 with the DATA dial. 9) Press CURSOR LEFT ( LAYER with the DATA dial. 10) Press CURSOR RIGHT (>) once and select your LAYER mode with the DATA dial. There are a few procedures to follow before you play the kit for the first time. Don’t play the kit while the TD-7T is warming up! When the unit is active, (after you see the Patch Page), the first thing you need to do is initialize the hi hat control pedal.
This will set up the FD-7 Hi Hat Controller for optimum performance results and will remain set even after the power is turned off. • Initializing 1) Power up while holding SYSTEM and JUMP. 2) Press ENTER. • Play the ROM Demos 1) Power up while holding ENTER. 2) Use the DATA DIAL to select the desired demonstration song. 3) Press the ENTER button to start the song. 4) Press EXIT to stop the song. 5) Press EXIT twice to return to Play mode. • Editing Sounds The TD-7T will allow you to make various types of edits to the sounds themselves. These Instrument Parameters include Pitch, Decay, Pan, Nuance, Brilliance, Pitch Bend, Output Levels and Effect Send Levels.
• Assigning Sounds/Layering The Instrument Section allows you to assign an instrument to each Note Number, allowing you to assign a different sound to each pad. You can also assign two different instruments to one Note Number, allowing you to create sounds through various mixing effects. This is called LAYER. The two instruments are called SOUND 1 and SOUND 2. To change the Instrument Parameters: 1) From the Patch Page, press EDIT. 2) Cursor to INST using the buttons and press ENTER. 3) Strike the pad or rim that will trigger the sound you wish to edit. 4) Cursor to the parameter and select the desired parameter using the DATA dial.
5) Push the CURSOR RIGHT button (>) once and change the value using the DATA dial. To assign an instrument to a note number: 1) Select your desired patch using the DATA dial. 2) From the Patch Page, press EDIT. 3) Cursor to PATCH using the buttons and press ENTER. 4) Cursor to NOTE and press ENTER. 5) Strike the pad or rim that will trigger the sound you wish to edit. 6) Cursor to the Instrument Number and select your Instrument with the DATA dial. NOTE: At the top of the display you'll find useful information concerning sound editing. EXAMPLE:
R1>N#35>S1>i081 R1 = Pad or Rim being edited (Rim number one) N#35 = MIDI Note Number assigned to this Pad or Rim S1 = Which sound in layer (S1 is Sound #1, S2 is Sound #2) i081 = Instrument Number assigned to Note Number being used. (number 81 out of 512) TBS64 © 1994 Roland Corporation U.S., 7200 Dominion Circle, Los Angeles, CA 90040 Faxback # 20063 6/97 NQPSMTR® '' EFC3@ G6CD:@? #6C4FDD:@? D@F?5 >@5F=6