Supermicro SAS-743TQ Backplane User's Guide PDF Download (EN)

S UPER ® MM2 MM2 MM3 MM3 SAS743TQ SAS743TQ REV 3.00 REV 3.00 R S UPER UPER pb pb M86 M86 M87 M87 M71 M71 M75 M75 M96 M96 M97 M97 M90 M90 M91 M91 H12 H12 H6 H6 H5 H5 H7 H7 49 49 48 48 16 16 64 64 1 H3 H3 +12V +12V +12V +12V GND GND GND GND GND GND GND GND +5V +5V +5V +5V SAS-743TQ Backplane USER'S GUIDE Rev. 1.0b

Стр. 1

SAS-743TQ Backplane User's Guide The information in this User’s Manual has been carefully reviewed and is believed to be accurate. The vendor assumes no responsibility for any inaccuracies that may be contained in this document, makes no commitment to update or to keep current the information in this manual, or to notify any person or organization of the updates. Please Note: For the most up-to-date version of this manual, please see our web site at www.supermicro.com. Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product described in this manual at any time and without notice.

This product, including software, if any, and documentation may not, in whole or in part, be copied, photocopied, reproduced, translated or reduced to any medium or machine without prior written consent. IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL, SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH HARDWARE, SOFTWARE, OR DATA.

Any disputes arising between manufacturer and customer shall be governed by the laws of Santa Clara County in the State of California, USA. The State of California, County of Santa Clara shall be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for all claims will not exceed the price paid for the hardware product. California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate” WARNING:

Handling of lead solder materials used in this product may expose you to lead, a chemical known to the State of California to cause birth defects and other reproductive harm. Manual Revision 1.0b Release Date: December 4, 2009 Unless you request and receive written permission from Super Micro Computer, Inc., you may not copy any part of this document. Information in this document is subject to change without notice. Other products and companies referred to herein are trademarks or registered trademarks of their respective companies or mark holders. Copyright © 2009 by Super Micro Computer, Inc. All rights reserved. Printed in the United States of America ii

Стр. 2

Safety Information and Technical Specifi cations Table of Contents Contacting Supermicro .......................................................................................iv Returning Merchandise for Service.....................................................................v Chapter 1 Safety Guidelines ....................................................................1-1 1-1 ESD Safety Guidelines ................................................................................... 1-1 1-2 General Safety Guidelines ..............................................................................

1-1 1-3 An Important Note to Users ............................................................................ 1-1 1-4 Introduction to the SAS-743TQ Backplane ..................................................... 1-2 Chapter 2 Jumper Settings and Pin Defi nitions ....................................2-1 2-1 Front Connectors and Jumpers ...................................................................... 2-1 Front Connectors ............................................................................................ 2-1 2-2 Front Connector and Pin Defi nitions ...............................................................

2-2 2-3 Front Jumper Locations and Pin Defi nitions ................................................... 2-4 I 2 C and SGPIO Mode Jumper Settings .......................................................... 2-6 SAS Port Connections in I 2 C and SGPIO Settings ....................................... 2-7 Front LED Indicators ....................................................................................... 2-8 2-4 Rear Connectors and LED Indicators ............................................................. 2-9 iii

Стр. 3

SAS-743TQ Backplane User's Guide Contacting Supermicro Headquarters Address: Super Micro Computer, Inc. 980 Rock Ave. San Jose, CA 95131 U.S.A. Tel: +1 (408) 503-8000 Fax: +1 (408) 503-8008 Email: marketing@supermicro.com (General Information) support@supermicro.com (Technical Support) Web Site: www.supermicro.com Europe Address: Super Micro Computer B.V. Het Sterrenbeeld 28, 5215 ML 's-Hertogenbosch, The Netherlands Tel: +31 (0) 73-6400390 Fax: +31 (0) 73-6416525 Email: sales@supermicro.nl (General Information) support@supermicro.nl (Technical Support) rma@supermicro.nl (Customer Support) Asia-Pacifi c Address: Super Micro Computer, Inc. 4F, No. 232-1, Liancheng Rd.

Chung-Ho 235, Taipei County Taiwan, R.O.C. Tel: +886-(2) 8226-3990 Fax: +886-(2) 8226-3991 Web Site: www.supermicro.com.tw Technical Support: Email: support@supermicro.com.tw Tel: 886-2-8226-1900 iv

Стр. 4