SAS-809T and SAS-809TQ.indb (EN)

S UPER ® MH3 MH2 J8 BZ1 C20 C85 C5 + + C26 #3 JP35 JP33 3 3 SIDEBAND 2-3:I2C 1-2:SGPIO JP33:MODE SEL 1 1 U25 + C32 C45 +5V GND GND +12V 1 4 JP10 JP51 C33 JP44 I2C MADE IN TAIWAN DESIGNED IN USA SAS-809T/TQ SAS-809T/TQ BACKPLANE USER'S GUIDE Rev. 1.0 3 1 C19 23 11 C65 +JP18 C84 C DD33:AA LARM 33 34 44C1U 51 19 5 + R71 J7 C159C15C7149 #1 J6 1 6 1 C18C44+ MH1 SA SAS809TQ J5#0 UPGRADE REV 1.01 JP46 2

Стр. 1

SAS-809T/TQ Backplane User's Guide The information in this User’s Manual has been carefully reviewed and is believed to be accurate. The vendor assumes no responsibility for any inaccuracies that may be contained in this document, makes no commitment to update or to keep current the information in this manual, or to notify any person or organization of the updates. Please Note: For the most up-to-date version of this manual, please see our web site at www.supermicro.com. Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product described in this manual at any time and without notice.

This product, including software, if any, and documentation may not, in whole or in part, be copied, photocopied, reproduced, translated or reduced to any medium or machine without prior written consent. IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL, SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH HARDWARE, SOFTWARE, OR DATA.

Any disputes arising between manufacturer and customer shall be governed by the laws of Santa Clara County in the State of California, USA. The State of California, County of Santa Clara shall be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for all claims will not exceed the price paid for the hardware product. FCC Statement: This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the manufacturer’s instruction manual, may cause harmful interference with radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case you will be required to correct the interference at your own expense. California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate” WARNING:

Handling of lead solder materials used in this product may expose you to lead, a chemical known to the State of California to cause birth defects and other reproductive harm. Manual Revision 1.0 Release Date: July 22, 2008 Unless you request and receive written permission from Super Micro Computer, Inc., you may not copy any part of this document. Information in this document is subject to change without notice. Other products and companies referred to herein are trademarks or registered trademarks of their respective companies or mark holders. Copyright © 2008 by Super Micro Computer, Inc. All rights reserved. Printed in the United States of America ii

Стр. 2

Safety Information and Technical Specifications Table of Contents Contacting Supermicro ..................................................................................................iv Returning Merchandise for Service ............................................................................ 2-1 Chapter 1 Safety Guidelines 1-1 ESD Safety Guidelines ................................................................................... 1-1 1-2 General Safety Guidelines .............................................................................. 1-1 1-3 An Important Note to Users ............................................................................

1-2 Chapter 2 Jumper Settings and Pin Definitions 2-1 Front Connectors and Jumpers ...................................................................... 2-1 2-2 Front Connector and Pin Definitions ............................................................... 2-2 2-3 Front Jumper Locations and Pin Definitions ................................................... 2-4 Explanation of Jumpers .................................................................................. 2-4 I 2 C and SGPIO Modes and Jumper Settings ................................................. 2-5 Front LED Indicators .......................................................................................

2-5 2-4 Rear Connectors and LED Indicators ............................................................. 2-6 Front Panel LEDs ............................................................................................ 2-5 Rear SAS/SATA Connectors ........................................................................... 2-6 Rear LED Indicators ........................................................................................ 2-6 iii

Стр. 3

SAS-809T/TQ Backplane User's Guide Contacting Supermicro Headquarters Address: Super Micro Computer, Inc. 980 Rock Ave. San Jose, CA 95131 U.S.A. Tel: +1 (408) 503-8000 Fax: +1 (408) 503-8008 Email: marketing@supermicro.com (General Information) support@supermicro.com (Technical Support) Web Site: www.supermicro.com Europe Address: Super Micro Computer B.V. Het Sterrenbeeld 28, 5215 ML Tel: +31 (0) 73-6400390 's-Hertogenbosch, The Netherlands Fax: +31 (0) 73-6416525 Email: sales@supermicro.nl (General Information) support@supermicro.nl (Technical Support) rma@supermicro.nl (Customer Support) Asia-Pacific Address: Super Micro Computer, Inc. 4F, No. 232-1, Liancheng Rd.

Chung-Ho 235, Taipei County Taiwan, R.O.C. Tel: +886-(2) 8226-3990 Fax: +886-(2) 8226-3991 Web Site: www.supermicro.com.tw Technical Support: Email: support@supermicro.com.tw Tel: 886-2-8226-1900 iv

Стр. 4