Schaublin · 70 · 12 pp.

Schaublin 70 Service Instructions: Comprehensive Guide for Industrial Users

Related manuals

Document text

SERVICE INSTRUCTIONS SCHAUBLIN 70 FABRIQUE Lone SCHAUBLIN S.A. 2735) SUISSE 2 < ow = jachine N° ¢—_________ AWB S— DE BEVILARD MACHINES |

Page 1

MACHINES E DE ctisss Byeairamrnpie SA SCHAUBLIN MOUNTING | THE 70 LATHE holes necessary for the in the sketches below : The are fixing shown Bed for overhead [ax 7 - ON A BENCH beds various 7o-10.000 and 1 the opening the for belts | | | | . 70-10,000 drive { /E | | ee i 1 ° |S) 1 St eyec“le F 2x70-10.002 et . | Mc | ere | ! | | jog 22 2 \) | || | \ Bod for underneath | 70-12,C00 drive 70-12 ae002 2 70-12,001 A \ Ij || i 4 i | 408 | ! q ——— 82 , 12 To prevent distortion of the profile of the bed on an iy LY insufficiently flat surface, the beds rest on three sphe- S/R LL, cs rical washers 70-10.003. Two sheetmetal plates _--~ 70-10.003 are ae = Se Ns supplied with the lathe.

Placed on prevent the they fa washers from eo digging into the wood. 7 After mounting check with a Ed. rule whether the bed is clear of and bench. the plates 24.8.1982 7 bench, the the ; LO ie __ | 2065.08085 ra “ 2115.00008 i 2101.00008 { {

Page 2

SCHAUBL Ree W12 VILARD. SUISSE IN 70 - 30/31.000 BALL~BEARING-MOUNTED / E HEADSTOCK SPECIFICATION Spindle-nose thread G22.6x2 mm 10 mm g23 mm Spindle bore g12 mm Maximum throughbore in standard collet $8.2 mm Spindel internal taper Length of spindle-nose Cylindrical Width thread seating of spindle nose 15° of pulley steps Diameter of pulley steps - 19 mm $ 46/62/78 mm Avticle Designation 70-30.000 Open headstock + manual drawbar 7.100 kg 70-30.060 Open headstock + quick-closing attachment 8.550 kg 70-31.000 Closed headstock + manual drawbar 8.300 kg 70-31.060 Closed headstock + quick-closing 9.750 kg The two spindle bearings to take up any play. Weight are preloaded.

attachment Consequently it will not be In normal conditions this preload is maintained throughout of the bearings. the period necessary of lubrication MAINTENANCE Cleaning on receipt Prior to despatch all external and internal machined special anti-rust grease. faces are given a coat of This grease has no lubricating properties, and its presence may cause serious seizures, even several weeks after commissioning of the machine. Clean the entire unit with in paraffin. a chemically neutral white rag (free from chlorine Avoid using alcohol, car petrol (which often contains alcohol), organic product that would dissolve the cellulose paint. Then cover all bare metal faces with lubricating oil. Ed.

: 30.1.1980 or acid) or any other t soaked i i

Page 3

Ss ETAT S755 sevwand “Suisse Lubricating the spindle bearings quick-closing attachment IN 70 - 30/31.000 / & and the bearings of the handlever-~operated The headstock bearings and those of the quick-closing attachment are lubricated for a period of about 5 years with Kliiber Isoflex LDS 18 Speciale A grease. For any subsequent immersion 1. method treatment of the bearings with this grease and select a clean, dust-free location use preferably for this purpose. Immerse the bearings in a receptacle filled with 1.1.1 tri-ethane chloride and leave them in this for 1 to 2 hours to allow the old coat of grease to dissolve. (In the absence turpentine 2, may of tri-ethane chloride oil of be used).

Fill a second receptacle with 1.1.1 tri-ethane chloride and shake the bearings in this without turning the races the one against the other. 3. Immerse the thus cleaned bearings in a solution of 70% 1.1.1 tri-ethane chloride and 30% Kliiber Isoflex LDS 18 Speciale A. After evaporation of the solvent the solution, penetrating the smallest crevices, ensures a uniform and lasting coat of grease. - Lubrication by oil gun The bearing cage 70-30. 609 and the pivot of the fork nipples for injecting oil by gun. Once a week inject a few shots of oil Use a good mineral oil of about 2.5° Light). DISMANTLING THE through E / 50° C 70-30.612 incorporate these nipples.

(for example MOBIL DTE Oil HEADSTOCK To lubricate or replace Proceed as follows : the bearings, the headstock must be dismantled. .1. Unhook 2. Loosen the two eccentrics 70-2.007 and 70-2.008 (in the closed headstock) or 70-30.006 (on the open headstock) and withdraw the headsto ck from the bed. 3. Withdraw 4. Undo the screw 2000.04008, secures the belt in the the drawbar the sleeve base. 70-32.030, which with the aid of the ring 70-30. 624, of the quick-closing attachment to the spindle. the

Page 4