Seres user manual (EN)

owner's manual MODEL NO. 247.886510 CAUTION: _/-___/_R,_ / CRRFT$M RN® Read INSTRUCTIONS carefully 23" - 5 H.P. DUAL STAGE SNOW THROWER Optional Electric Starter Available =Assembly =Operation =Maintenance =Repair Parts Sold by Sears, Roebuck and Co., Chicago, IL 60684 Part No. 770-6870D

Стр. 1

CRAFTSMAN WARRANTY' LIMITED TWO YEAR WARRANTY ON CRAI_SMAN SNOW THROWER For two years from the date of purchase, whet this Craftsman Snow Thrower is maintained, lubricated and tuned up according to the instructions in the owner's manual, Sears will repair, free of charge, any defect in material and workmanship. If this Craftsman Snow Thrower is used for c ;mmercial or rental purposes, this warranty applies for only 90 days from the date of purchase. This warranty does not cover: Expendable terns which become worn during normal use, such as spark plugs, tire chains and shear pins.

Repairs necessary because of operator aL use or negligence, including bent cranksh_,ffs and the failure to maintain WARRANTY SERVICE IS AVAILABLE BY CO _ITACTING THE NEAREST SERVICE CENTER/DEPARTMENT IN THE the equipment according to the instructk ns contained in the owner's manual. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. UNITED STATES. This warranty applies only while this product is in use in the United States. SEARS, ROEBUCK AND CO. DEP' r. 698/731A SEARS TOWER CHICAGO, IL 60684 OWNEF:'S INFORMATION Record the following information about youl unit so that you will be able to provide it in case of loss or theft.

DATE PURCHASED:. MODEL NO./CODE: 247.886510L STORE WHERE PURCHASED: ADDRES_ CITY: STATE: TELEPHONE: MAINTENANCE AGREEMENT A SEARS MAINTENANCE AGREEMENT IS AVAILABLE FOR THIS PRODUCT. CONTACT YOUR NEAREST SEAR S STORE FOR DETAILS. TABLF OF CONTENTS Page CRAFTSMAN WARRANTY ................. 2 OWNER'S INFORMATION .................. 2 MAINTENANCE AGREEMENT .............. 2 SAFE OPERATION PRACTICES ............. 3 ASSEMBLY INSTRUCTIONS .............. 4-9 OPERATING INSTRUCTIONS ........... 10-13 MAINTENANCE ..................... 13, 14 Page STORAGE ........................... 14, 15 ADJUSTMENT/REPAIRS ............... 15-19 TROUBLE SHOOTING GUIDE ............. 20 SNOW THROWER REPAIR PARTS ......

22-29 ENGINE REPAIR PARTS ............... 30-34 HOW TO ORDER REPAIR PARTS .. Back Cover

Стр. 2

IMPOR ANT SAFE OPERATION PRACTICES FOR WALK-BEHIND SNOW THROWERS _lb THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH, IF NOT FOLLOWED COULD ENDANGER THE PERSONAL SAFETY AND/OR PROPERTY OF YOURSELF AND OTHERS. READ AND FOLLOW ALL INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE YOUR SNOW THROWER. To reduce the potential for any injury, comply with the following safety instructions. Failure to comp|y with the instructions may result in personal injury. TRAINING 5_ Stop engine whenever you leave the operating position, before unclogging the augerlimpel_,r housing or discharge guide, and making any repairs, adjustments, or inspections. 1. Read this owner's guide carefully.

Be thoroughly familiar with the controls and proper use of the equipment. Know how to stop the unit and disengage the controls quickly. 2. Never allow children to operate equipment. Never allow adults to operate equipment without proper instructions. 6. Take all possible precautions when leaving the unit un- attended. Disengage the auger/impeller, shift into neutral, stop the engine, and remove the key. 3. No one should operate this unit while intoxicated or while taking medication that impairs the senses or reactions. 7. When cleaning, repairing, or inspecting, make certain auger/impeller and all moving parts have stopped.

Discon- nect spark plug wire and keep away from plag to prevent accidental starting. 4. Keep the area of operation clear of all persons, especialLy small children and pets. 5. Exercise caution to avoid slipping or falling, especially when operating in reverse. 8. Do not run engine indoors, except when starting engine and transporting snow thrower in or out of building. Open doors. Exhaust fumes are dangerous. PREPARATION 1. Thoroughly inspect the area where the equipment is to be used and remove all door mats, sleds, boards, wires and other foreign objects. 9. Do not clear snow across the face of slopes. Exercise ex- treme caution when changing direction on slopes.

Do not at- tempt to clear steep slopes. 10. Never operate snow thrower without guards, plates, or other safety protection devices in place. 2. Disengage all clutches and shift into neutral before starting engine. 11. Never operate snow thrower near glass enclosures, automobiles, windows wells, drop offs, etc., without proper adjustment of snow thrower discharge angle. Keep children and pets away. 3. Do not operate equipment without wearing adequate winter outer garments. Wear footwear which will improve footing on slippery surfaces. 4. Check the fuel before starting the engine. Gasoline is an ex- tremely flammable fuel.

Do not fill the gasoline tank indoors, while the engine is running, or while the engine is still hot. Replace gasoline cap securely and wipe off any spilled gasoline before starting the engine as it may cause_a fire or explosion. 12. Do not overload machine capacity by attempting to clear snow at too fast a rate. 13. Never operate the machine at high transport speeds on slip- pery surfaces. Look behind and use care when backing. 14. Never direct discharge at bystanders or allow anyone in front of unit. 5. Use a grounded three wire plug-in for all units with electric drive motors or etectric starting motors. 15. 6. Adjust auger housing height to clear gravel or crushed rock surface.

Disengage power to auger/impeller when transporting or not in use. 7. Never attempt to make any adjustments while engine is run- ning (except where specifically recommended by manufacturer). 16. Use only attachments and accessories approved by the manufacturer of snow thrower (such as wheel weights, counterweights, cabs, etc.). 17. Never operate the snow thrower without good visibility or light. Always be sure of your footing and keep a firm hold on the handles. Walk, never run. 8. Let engine and machine adjust to outdoor temperature before starting to clear snow. 9.

Always wear safety glasses or eye shields during operation or while performing an adjustment or repair, to protect eyes from foreign objects that may be thrown from the machine in any direction. MAINTENANCE AND STORAGE OPERATION 1. Check shear bolts, engine mounting bolts, etc., at frequent intervals for proper tightness to be sure equipment is in safe working condition. 1, Do not put hands or feet near rotating parts. Keep clear of discharge opening at all times. 2. Exercise extreme caution when operating on or crossing gravel drives, walks, or roads. Stay alert for hidden hazards or traffic. Do not carry passengers. 2.

Never store the machine with fuel in the fuel tank inside a building where ignition sources are present, such as hot water and space heaters, clothes dryers, and the like. Allow engine to cool before storing in any enclosure. 3. After striking a foreign object, stop the engine, remove wire from spark plug, and thoroughly inspect the snow thrower for any damage. Repair the damage before restarting and operating the snow thrower. 3. Always refer to owner's manual instructions for important details if snow thrower is to be stored for an extended period. 4. If the snow thrower should start to vibrate abnormally, stop the engine and check immediately for the cause.

Vibration is generally a warning of trouble. 4. Maintain or replace safety and instruction labels, as necessary. 5. Run machine a few minutes after throwing snow to prevent freeze up of auger/impeller.

Стр. 3

ASSEMBLY INSTRUCTIONS Handle Right Panel , . Hand P] Assembly _ _-====_==,_1_ Lower Han_dleI1 [L_ I_ "_ _'HL PPd_r \\t_s JJ e,, I1_ NOT E Reference to right and left side of the snow thrower is from the operator's position at the handle. TOOLS REQUIRED FOR ASSEMBLY 1 Knife (to cut carton) 2 1/2" Wrenches (or Adjustable Wrenches) 1 Pair of Pliers 1 9/16" Wrench (or Adjustable Wrench) 1 7/16" Wrench (or Adjustable Wrench) --_---CONTENTS OF SHIPPING CARTON (See figure 1) "_.'_ ._',F Hand !;hift Traction Driv_ _'_ _ h_nw_ /:iod Cable Assembly__ _ L _=_ Augers, Cable I Chute Cra!k Assembly 1. Snow Thrower (not shown) 2. Lower Handles--R.H. and L.H. 3. Handle Panel Assembly 4.

Upper Handle Assembly 5. Traction Drive Cable Assembly 6. Auger Cable 7. Parts taped together which include: Shift Rod Chute Crank Assembly 8. Hardware Pack (plastic bag) which contains the hardware shown in figure 2 (shown actual size), plus one chute crank bracket and two ignition keys which are not shown. 9. Tire Chains (not shown) E q q FIGURE 1. Hand Knobs 5/16" Cupped Wa _ers Bolts----_ 2" Long Cotter ins 3/8" I rriage Bolt 2" Long Clip --LJ Spare Shear _---Bolts Carriage Its 21/2" Long Spare Hex Lock I Carriage 5/16" Flat Washer 3/4" Long FIGURE 2.

Стр. 4