SEARS - owner's manual - Home Depot Repair Parts

f Save This Manual For Future Reference SEARS owner's manual Model No. 113.299210 Saw with Legs Two Table Extensions Motor Rip Fence and Miter Gauge Serial Number. Model and sedal numbers may be found on the left rear side of the base, ® 10 iNCH DIRECT DRIVE TABLE SAW You should record both model and serial number in a safe place for future use, FOR YOUR - assembly . operating o repair parts READ ALL INSTRUCTIONS CAREFULLY J Sears, Roebuck and Co., Hoffman Estates, IL. 60179 U_S,A. Part No, SP5909 Printed in US A

Page 1

FULL ONE YEAR WARRANTY ON L,RAFTSNIAN STATIONARY TOOL If this stationary tool fails due to a defect in material or workmanship within one year from the date of purchase, CONTACT THE NEAREST SEARS SERVICE CENTER IN THE UNITED STATES and Sears wilt repair it free of charge. This warranty applies only while this product is in the United States. If this Table Saw is used for commercial or rental purposes, this warranty will apply for ninety days from the date of purchase. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Sears, Roebuck and Co°, D/817 WA Hoffman Estates, IL 60179 .

.._ Safety Instructions For Table Saw Safety is a combination of common sense, staying alert and knowing how your table saw works,, Read this manual to understand this table saw Safety Signal Words WARNING: means if the safety information is not foUowed someone could be seriously injured or killed, DANGER: means if the safety information is not followed someone will be seriously injured or killed CAUTION: means if the safety information is not followed someone may be injured, Before Using The Saw WARNING:

to avoid mistakes that could cause blade tilt controls (See "Getting to Know Your Table Saw" section), serious, permanent injury, do not plug the table saw in until the following steps have been satis- factorily completed. . Review and understand all safety instructions and operating procedures in this manual.

* Completely assemble and align saw (See "Assembly" section) ° Learn the use and function of the ON-OFF switch blade guard, spreader, anti-kickback device, miter gauge, rip fence, table insert, blade elevation and , Review the maintenance methods for this saw (See "Maintaining Your Table Saw" section)), - Find and read all the warning labels found on the saw (shown below), m ® , WARNING 1, Read manual before using saw. 2. Wear safety gogglesthat meet ANSI Z87.1Standards, ' 3. DOnot reach around or over saw blade. 4. Keep blade guard downend In place for throughcuts. 5. Do not do freehand cuts. 6. Keep hands out of path of saw blade° 7.

When ripping,use push stickwhen fence Is set 2 Inches or more from blade. 8,, Know how to reduce therisk of kickback, See Instructions for ripping, 9. When rlpNng, use push block and auxiliary fence wher fenceIs set between1/2end 2 Inches from blade. Do not make dp cuts narrowerthan 1/2 ]nch_ l& Turn power off endwalt for bladeto stop before adjustingor servicing. 12o VoIts 3450 RP M E23417 1 t 5 Amp._ 60 Hz_ I Ph I0" Blade When Installing Or Moving The Saw Avoid Dangerous Environment.

Use the saw in a dry, indoor place protected from rain, Keep work area well lighted Use recommended accessories Consult the owneCs manual Ior recommended accessories, The use of o When using a table extension longer than t2" attached to any side of the saw, bolt the saw to a stationary sur_ face or prop up the outer end of the extension from the floor or bench top to keep the saw from tipping o Put the saw where neither operator nor bystanders must stand in line wilh the sawblade, To avoid injury from unexpected saw movement. .

Bott or clamp the saw to firm level surface where there is plenty of room to handle and properly support the work- piece (See "Assembly-Mounting Your Saw" section) ° Support the saw so the table is level and the saw does not rock improper accessories may cause risk of injury to persons ° To avoid injury from electrical shock, make sure your fingers do not touch the plug's metal prongs when plugging in or unplugging the saw, Never Stand On Tool Serious injury could occur if the tool tips or you accidentally hit the cutting tool Do not store anything above or near the tool where anyone might stand on the tool to reach them,

Page 2

Before Each Use ° Replace damaged or missing parts before using the saw again, Inspect your saw, - To avoid injury from accidental starting, turn the switch off, unplug the saw, and remove the switch key before raising or removing the guard, changing the cutting tool. changing the setup, or adjusting anything Make sure switch is in OFF position before plugging in, * Keep guards in place and in working order .

Use the sawblade guard, spreader and anti-kickback pawls for any thru-sawing (whenever the blade comes through the top of the workplace) Make sure the anti- kickback pawls work properly Make sure the spreader is in line with sawblade (See "Assembly-Aligning Blade Guard" section) ° Remove adjusting keys and wrenches Form a habit of checking for and removing keys and adjusting wrenches from table top before turning saw on Check for alignment of moving parts, binding of moving parts, breakage of parts, saw stability, and any other conditions that may affect the way the saw works If any part is missing, bent or broken in any way.

or any electrical part does not work properly, turn the saw off and unplug the saw o Make sure all clamps and locks are tight and no parts have excessive play To Avoid Injury From Jams, Slips Or Thrown Pieces (Kickbacks Or Throwbacks) Inspect Your Blade. Inspect your workpieceo Choose the right blade or cutting accessory for the Make sure there are no nails or foreign objects in the material and the type of cutting you plan to do. part of the workpiece to be ctJt, o Use The Right Tool. Don't lorce tool or attachment to . When cutting irregularly shaped workpieces, plan your do a job it was not designed for work so it will not slip and pinch the blade: .

Never use grinding wheels, abrasive cutoff wheels, ° A piece of molding for example, must lie flat or be held friction wheels (metal cutting blades) wire wheels or by a fixture or jig that will not let it twist, rock or slip buffing wheels, They can fly apart explosively while being cut Use jigs or fixtures where needed to Cut only wood, wood like or plastic materials Do not prevent workpiece from shifting cut metal Use a different, better suited type of tool for work that . Choose and inspect your cutting tool carefully:

can't be made stable -To avoid cutting tool failure and thrown shrapnel Plan your cut, (broken pieces of blade), use only 10" or smaIler ° To avoid kickbacks and throwbacks - when a part or all blades or other cutting tools marked for speeds of of the workpiece binds on the blade and is thrown vio- 5000 rpm or higher lently back toward the front of the saw: - Always use unbroken, balanced blades designed to - Never cut Freehand.

Always use either a rip fence, fit this saw's 5/8 inch arbor miter gauge or fixture to position and guide the work, - When thru-sawing (making cuts where the blade so it won't twist or bind on the blade and kick back comes through the workpiece top), always use a 10 - Make sure there's no debris between the workpiece inch diameter blade This keeps the spreader closest and its supports to the blade - Use extra caution with large, very small or awkward - Do not over tighten arbor nut Use arbor wrenches to workpieces, "snug" it securely, o Use extra supports (tables, saw horses, blocks, etc) - Use only sharp blades with properly set teeth.

Corn for any workpieces {arge enough to tip when not held suit a professional blade sharpener when in doubt down to the table top Never use another person as a - Keep blades clean of gum and resin substitute for a table extension, or as additional sup- - Never use the saw without the proper blade insert port for a workpiece that is longer or wider than the basic saw table, or to help feed, support or pull the Inspect your work area. workplace ,, Keep work area clean, Never confine the piece being cut off, that is, the piece . Cluttered areas and benches invite accidents Floor not against the rip fence, mitel gauge or fixture Never must not be slippery from wax or sawdust hold it, clamp it.

touch it, or use length stops against it oTo avoid burns or other fire damage, never use the It must be free to move If confined, it could get saw nearflammabte liquids, vapors or gases wedged against the blade and cause a kickback or To avoid injury, don't do layout, assembly, or setup throwback work on the table while blade is spinning It could cut * Never cut more than one workpiece at a time ! or throw anything hitting the blade o Never tum your table saw "ON" before clearing every- Plan yourwork thing except the workpiece and related support Use the right toot Don't force tool or attachment to do devices off the table a job it was not designed for

Page 3

Safety Instructions For Table Saws (continued) Plan Ahead To Protect Your Eyes, Hands, Face and Ears Dress for safety Do not wear loose clothing, gloves, neckties or jewelry (rings, wrist watches) They can get caught and draw you into moving parts Plan the way you will push the workpiece through° - Never pull the workpiece through, Start and finish the cut from the front of the table saw,, Wear nonslip footwear Never put your fingers or hands in the path of the sawblade or other cutting tool, . Tie back long hair, ° Never reach in back of the cutting tool with either hand to hold down workpiece, support the workpiece.

remove wood scraps, or for any other reason Roll long sleeves above the elbow Noise levels vary widely To avoid possible hearing damage, wear ear plugs or muffs when using table saw for hours at a time ° Avoid hand positions where a sudden slip could cause fingers or hand to move into a sawblade or other cut- ting too!

Any power saw can throw foreign objects into the eyes, This can result in permanent eye damage, Wear safety goggles (not glasses) that comply with ANSI Z87 1 (shown on package), Everyday eyeglasses have only impact resistant lenses They are not safety glasses, Safety goggles are available at Sears retail stores Glasses or goggles not in compliance with ANSI Z87.1 could seriously hurt you when they break, Don't overreach., Always keep good footing and balance o Push the workpiece against the rotation of the blade, never feed material into the cutting tool from the rear of the saw, ° Always push the workpiece all the way past the saw- blade ° As much as possible, keep your face and body to one side of the sawblade, out of line with a possible kick _ back or throwback WEAR YOUR o Set the cutting tool as low as possible for the cut you're planning Avoid Accidental Starting.

° For dusty operations, wear a dust mask along with safety goggles - Make sure switch is "OFF" before pltJgging saw into a power outlet WARNING: Don't allow familiarity (gained from fre- quent use of your table saw) to cause a careless l mistake,. Always remember that a careless fraction of a second is enough to cause a severe injury. , ,,11 ........ H,, .... , i, ,,,1 Whenever Sawblade Is Spinning Before freeing jammed material.

o Turn switch "OFF" Wait for aFImoving parts to stop Before actually cutting with the saw, watch it while it runs for a short while if it makes an unfamiliar noise or vibrates a lot, stop immediately Turn the saw off Unplug the saw Do not restart until finding and cor- recting the problem, . Unplug the saw ° Check blade, spreader and fence for proper alignment before starting again. To avoid throwback of cut off pieces. ° Use the guard assembly Make sure the top of the arbor or cutting tool turns toward the front of the saw To remove loose pieces beneath or trapped inside the guard. o Turn saw "OFF" Keep Children Away, o Keep all visitors a safe distance from the table saw.

o Make sure bystanders are clear of the table saw and workpiece Don't Force Toot. ° Remove switch key Before Leaving The Saw. - Turn the saw off - Wait for blade to stop before lifting the guard Let the blade reach fu!t speed before cutting ° Wait for blade to stop spinning ° It will do the job better and safer at its designed rate . Unplug the saw Make workshop child-proof Lock the shop Disconnect master switches Remove the yellow switch key Store it away from children and others not qualified to use the took o Feed the workpiece into the saw only fast enough to let the blade cut without bogging down or binding

Page 4