SuperServer 5019S-ML User's Manual Chapter 6: BIOS SATA Mode Selection SATA Port 0~ Port 7 Use this item to select the mode for the installed SATA drives. The options are AHCI and RAID. This item displays the information detected on the installed SATA drive on the particular SATA port. SATA Frozen Use this item to enable the HDD Security Frozen Mode. The options are Enabled and Disabled . Port 0~ Port 7 The status of a SATA port will be displayed as detected by the BIOS. *If the item above "Configure SATA as" is set to AHCI, the following items will display:
Port 0 ~ Port 7 Software Preserve SATA Port 0~ Port 7 The status of software preserve of a SATA port will display as it is detected by the BIOS. This item displays the information detected on the installed SATA drive on the particular SATA port. Port 0 ~ Port 7 Hot Plug This feature designates the port specified for hot plugging. Set this item to Enabled for hot- plugging support, which will allow the user to replace a SATA disk drive without shutting down the system. The options are Enabled and Disabled . Port 0~ Port 7 The status of a SATA port will be displayed as detected by the BIOS.
Port 0 ~ Port 7 Software Preserve Port 0 ~ Port 7 Spin Up Device The status of software preserve of a SATA port will display as it is detected by the BIOS. On an edge detect from 0 to 1, set this item to allow the PCH to initialize the device. The options are Enabled and Disabled . Port 0 ~ Port 7 Hot Plug This feature designates the port specified for hot plugging. Set this item to Enabled for hot- plugging support, which will allow the user to replace a SATA disk drive without shutting down the system. The options are Enabled and Disabled .
Port 0 ~ Port 7 SATA Device Type Use this item to specify if the SATA port specified by the user should be connected to a Solid State drive or a Hard Disk Drive. The options are Hard Disk Drive and Solid State Drive. Port 0 ~ Port 7 Spin Up Device PCIe/PCI/PnP Configuration On an edge detect from 0 to 1, set this item to allow the PCH to initialize the device. The options are Enabled and Disabled . The following information will display: Port 0 ~ Port 7 SATA Device Type PCI Bus Driver Version Use this item to specify if the SATA port specified by the user should be connected to a Solid State drive or a Hard Disk Drive. The options are Hard Disk Drive and Solid State Drive.
PCI Devices Common Settings: PCI Latency Timer *If the item above "SATA Mode Selection" is set to RAID, the following items will display: Use this feature to set the latency Timer of each PCI device installed on a PCI bus. Select 32 to set the PCI latency to 32 PCI clock cycles. The options are 32 PCI Bus Clocks , 64 PCI Bus Clocks, 96 PCI Bus Clocks, 128 PCI Bus Clocks, 160 PCI Bus Clocks, 192 PCI Bus Clocks, 224 PCI Bus Clocks, and 248 PCI Bus Clocks. SATA RAID Option ROM/UEFI Driver Select UEFI to load the EFI drvier for system boot. Select Legacy to load a legacy driver for system boot. The options are Legacy ROM and UEFI Driver.
PCI PERR/SERR Support Select Enabled to support PERR (PCI/PCI-E Parity Error)/SERR (System Error) runtime error reporting for a PCI/PCI-E slot. The options are Enabled and Disabled. SATA Frozen Use this item to enable the HDD Security Frozen Mode. The options are Enabled and Disabled . Above 4G Decoding (Available if the system supports 64-bit PCI decoding) Select Enabled to decode a PCI device that supports 64-bit in the space above 4G Address. The options are Enabled and Disabled . 75 74