Supermicro SuperServer 5019S-ML — 6.3 Advanced Setup Configurations

SuperServer 5019S-ML User's Manual Chapter 6: BIOS PCH SLOT4 PCI-E 3.0 X4 (IN X8) OPROM PXE boot wait time Use this feature to select which firmware type to be loaded for the add-on card in this slot for system boot. The options are Disabled, Legacy , and EFI. Use this option to specify the wait time to press the ESC key to abort the PXE boot. Press "+" or "-" on your keyboard to change the value. The default setting is 0 . PCH SLOT5 PCI-E 3.0 X8 OPROM Media detect count Use this feature to select which firmware type to be loaded for the add-on card in this slot for system boot. The options are Disabled, Legacy , and EFI. Use this option to specify the number of times media will be checked.

Press "+" or "-" on your keyboard to change the value. The default setting is 1 . PCH SLOT6 PCI-E 3.0 X8 (IN X16) OPROM Super IO Configuration Use this feature to select which firmware type to be loaded for the add-on card in this slot for system boot. The options are Disabled, Legacy , and EFI. The following Super IO information will display: AMI SIO Driver Version Onboard LAN Option ROM Type Select Enabled to enable Option ROM support to boot the computer using a network device specified by the user. The options are Legacy and EFI.

Super IO Chip Logical Device(s) Configuration Serial Port 1 Onboard LAN1 Option ROM Serial Port 1 Configuration Use this option to select the type of device installed in LAN Port1 used for system boot. The default setting for LAN1 Option ROM is PXE . This submenu allows the user the configure settings of Serial Port 1. Onboard LAN2 Option ROM/Onboard LAN3 Option ROM/Onboard LAN4 Option ROM (LAN3 Option ROM/Onboard LAN4 Option ROM: Available on the X11SSH-LN4F only) Serial Port 1 Select Enabled to enable the selected onboard serial port. The options are Enabled and Disabled. Use this option to select the type of device installed in a LAN port specified by user for system boot.

The default setting for this item is Disabled . Logical Device Settings Onboard Video Option ROM This item displays the current status of a serial part specified by the user. Use this item to select the Onboard Video Option ROM type. The options are Disabled, Legacy, and EFI. Serial Port 1 Change Settings VGA Priority This feature specifies the base I/O port address and the Interrupt Request address of a serial port specified by the user. Select Auto to allow the BIOS to automatically assign the base I/O and IRQ address. Use this item to select the graphics device to be used as the primary video display for system boot. The options are Onboard and Offboard.

The options for Serial Port 1 are Use Automatic Settings , (IO=3F8h; IRQ=4; DMA), (IO=3F8h; IRQ=3, 4, 5, 7, 9, 10, 11, 12; DMA), (IO=2F8h; IRQ=3, 4, 5, 7, 9, 10, 11, 12; DMA), (IO=3E8h; IRQ=3, 4, 5, 7, 9, 10, 11, 12; DMA), and (IO=2E8h; IRQ=3, 4, 5, 7, 9, 10, 11, 12; DMA). Network Stack Select Enabled to enable PXE (Preboot Execution Environment) or UEFI (Unified Extensible Firmware Interface) for network stack support. The options are Enabled and Disabled. Serial Port 2 IPv4 PXE Support Serial Port 2 Configuration Select Enabled to enable IPv4 PXE boot support. The options are Enabled and Disabled. This submenu allows the user the configure settings of Serial Port 2.

IPv6 PXE Support Serial Port 2 Select Enabled to enable IPv6 PXE boot support. The options are Enabled and Disabled . Select Enabled to enable the selected onboard serial port. The options are Enabled and Disabled. 77 76