7 7.4 7.4.2 DC-bus operation Rated data DC-supply power 7.4.2 DC-supply power The parameters relevant for the selection of a supply unit with a suitable supply power (even in the overload range) are listed in the below table: U Lr Rated AC voltage Cycle 1 Cycle for the second-range Cycle 2 Cycle for the minute-range P DC 100% Permanent power of DC-voltage level P ol Power during overload t ol Overload time P re Power during relief t re Relief time Any other cycles are calculated with the following formula: ( P ol ⋅ t ol ) + ( P re ⋅ t re ) t ol + t re ≤ P DC 100% Cycles other than the above cycles must not exceed the specified power and time values, i.e.
the values must be used as maximum values. The values depend on the rated AC voltage U Lr . 230 V Supply modules ( + filter) Single Drives Tab.
7.4-2 7.4-2 EDS94SPP101 EN 3.1-04/2007 Supply power ULr = 230 V Cycle 1 Cycle 2 Type PDC 100% [kW] Pol · tol [kW] · [s] Pre · tre [kW] · [s] Pol · tol [kW] · [s] Pre · tre [kW] · [s] E94APNE0104 2.1 8.4 · 0.5 1.6 · 4.5 3.2 · 60 1.6 · 120 E94APNE0104 + E94AZMP0084 2.8 11.2 · 0.5 2.1 · 4.5 4.2 · 60 2.1 · 120 E94APNE0364 7.5 22.5 · 0.5 5.6 · 4.5 11.3 · 60 5.6 · 120 E94APNE0364 + E94AZMP0294 10.1 30.3 · 0.5 7.6 · 4.5 15.5 · 60 7.6 · 120 E94ASxE0024 + E94AZMS0034 1.2 3.8 · 0.5 0.9 · 4.5 1.8 · 60 0.9 · 120 E94ASxE0034 + E94AZMS0034 1.2 3.9 · 0.5 0.9 · 4.5 1.8 · 60 0.9 · 120 E94ASxE0044 + E94AZMS0094 2.0 6.4 · 0.5 1.5 · 4.5 3.0 · 60 1.5 · 120 E94ASxE0074 + E94AZMS0094 3.4 8.1 · 0.5 2.6 · 4.5 5.1 · 60 2.6 · 120 E94ASxE0134 + E94AZMS0314 6.1 14.6 · 0.5 4.6 · 4.5 9.2 · 60 4.6 · 120 E94ASxE0174 + E94AZMS0314 7.8 18.7 · 0.5 5.9 · 4.5 11.7 · 60 5.9 · 120 E94ASxE0244 + E94AZMS0314 11.0 22.0 · 0.5 8.3 · 4.5 16.5 · 60 8.3 · 120 E94ASxE0324 20.1 40.2 · 0.5 15.1 · 4.5 30.2 · 60 15.1 · 120 E94ASxE0474 20.1 40.2 · 0.5 15.1 · 4.5 30.2 · 60 15.1 · 120 E94ASxE0594 20.1 40.2 · 0.5 15.1 · 4.5 30.2 · 60 15.1 · 120 E94ASxE0864 39.1 78.2 · 0.5 29.3 · 4.5 58.7 · 60 29.3 · 120 E94ASxE1044 39.1 78.2 · 0.5 29.3 · 4.5 58.7 · 60 29.3 · 120