— AMCP 706-286 — Engineering Design Handbook (1963)

Downloaded from https://www.everyspec.com STRESS ANALYSIS ' stress T, in pure torsion is : - circular median line of ihe wall are prevented 3-4.4. Pure Torsion. The cr'tical shear and circumferential di'qplacement of the in the end sections. 7, = E(hiL)213.08 + J3._5 When the end section of the cylinder is + 0.557(L-'/hR)"I,-1 (3 27 welded or bolted to another structural ele- if Poisson's raiio is taken as 0.3.'.5 ment, warping of the plane and rotation of For very long cylinders the fohlowing the generators may be partially or fully pre- formula applies: vented.

This additional constraint raises the (328 critical stress but the increase is usually not =0.25 E' (h,;R/ "- 2 (32) signifficant excepi when the cylinder is very 3-4.5. Hydrostatic Pressure. In the hydro- shict en the clinde ve static case of loading, the cylinder is closed short. In the latter case more accurate values at its two ends and the closed shell is sub- of the bucking stress can be taken from the lIterature2.-'| jected to a uniform external pressure p. d When the cylinder is very long, it buckles 3-4.8. Stabiization Through Internal Pres- under the critical pressure corresponding to sure.

Thin shells can be partially, or fully, uniform lateral pressure; and when it is very stabilizedI through application of an inter- short, under the critical strew- of the axial nal pressure p. The stabilizing effect in the loading case. In the range between these two case of a circular cylindrical shell subjected extremes the critical pressure of the hydro- to a uniformly distributed axial compressive static loading case is lower than the c-itical stress can b expresed by an addi.ion of -k pressure of either of the simpler loading to the value k .of the factor in Equation cases mentioned. For exact values, see the (3-25).

First calculate the non-dimensional literature.' - 2 An approximate formula can pressure p* defined as be given as p* = (p/E)(R/h)2 (3 31) )0.92 E (h/R)y The increment Ak is then qiven by P " (I,/R)(R.,h)' , - 0.636 (3 29) Ak = 1.9 pi if 0 p* 0.12 (3 32) 2-4.6. Combined Axial Compression and Ak = 0.229 if *> 0.12 Torsion. An empirical formula - can be given Finally, Equation (3 2ti) is replaced by in the form: (k + Ak) E (h/R) (3-33) R, +i- R,- 1 (3 30) If the example given under Paragraph 3-4.2 is In this interaction formula R,.

is the ratio of continued ard ar, internal pressure p = 10 psi the compressive stress of the combined load is applied to the she)l, one obtains p' = 0.0862 and ak = 0.164. Hence the critical stress ing to the critical compressive stress under b compression alone, and R, :% the ratio of the shear stress of the combined !oading to t)l, o,, = 0.24 x 29 X i0/500 - 13,900 psi with- critical shear stress of torsion !:'.se. When out internal pressure 0 ,= 0.404 x 29 x 10/500 = 23,450 psi the inequality is sat;:.ca, the cylindrical wi.h internal pressure shell is safe. W en the left-hand member of Young's Modul~s was assumed to be 29 X 106 the ineo,aty is Lqual to unity, the shell s buck'es.

No equilibrium can be maintained A limited amount of experimental evi- 4nen the left-hand member exceeds unity. dence - indicates that Equation (3-30) can be 3-4.?. Different Boundary Conditions. The used to determine the critical condition of a equations given above are valid for the case circular cylindrical shell subjected simulta- when the edges af the cylinder are simply neously to compres;ioa, tursion and internal supported. This boundary condition invc'ves pressure'. It is only necessary to re-interpret no constraint against rotation of the gem ra- the meaning of the symbols R, and 9,.

R, is tors of the cylinder over the supports and no nox the ratio of the applied I coinpressive resistance to a warping of the end section of stress of the triple loading (compression plus the cylinder out of its plane; however, radial torsion plus pressure) to the "ritical corn. 45 , g