— AMCP 706-286 — Engineering Design Handbook (1963)

Downloaded from https://www.everyspec.com kSTRUCTURES where the constant Btu b.a. .,e dimension crocp; i.Ns is characterized by = in . of a t..mperature. Equations (3-53) and (3r62). L% . ar creep Although the.;e formulas represent the re- is occasiorm-ly observed with high polymers ". suits of constant-stress tests, tbey have been but not with metals. generally used under variable stress condi- Since the material, in general, is subject tions also. They are more likely to gve re- to elastic deformations even though crr-ep liable results during loading than during un- deformations are also present, the Fress loading.

The values of n in ballistic missile distribution caused by a prescribed lo-ding applications usually range between 3 and 15. depends on the interaction betwean elasticity and creep, and it changes with time. At the 3-8.2. Primary Creep. During the primary moment when the loads are applied, the ~~stage of creep the creep r~te changes with lna isi iti ui np r al.W t n time. Results of tests carried out at constant creasing tic thi changes over into oe that tress and constant tPemperaturie can usually is governed by the creep law alone.

be represented as This final distribution is the some whether o =k4 ) ' (&-62) the creep phenoiieron is re.presented by However, this equation is unsuitable under Equation (3-58) ;cr secondary creep or conditions of variable stress. It can be Equation (3-62) for primary creep as long brought into a form in which time does not as the value of. n ir. the same. Its analysis appear explicitly; this is necessary because can be carried out with the aid of analogues the presence of t in a formula representing and minimal principles derived in the lit- creep strain leads to logical inconsistencies erature" "- undr variable stress conditiono.

Discussion As an example, the results of the analysis of this can be found in the literature.'" This of the stress distribution in a solid rectang- assumption on which the transformation is ular beam subjected to a constant bending i Abased is that the creep rate at constant tern- moment may be presented. If h is the depth - perature Js only a function of the instantane- of the beam and y the distance measured ous values of stress and strain but not of the frcrn the neutral axis of the cross section, the history of loading. This assumption implies distribution of the normal stresses (bending the ei istence of a mechnical equa'ion of state.

stresses) is characterized by the equation The recommended formulation is N s. (Y4 X)', o/c, (2ylh);"' (3-64) = p--"-,,--- (3-63) where ,,,,,. is the stress in the extreme fiber -,here the constants have the same values as and n is the exponent in the creep law. The in Equation (3-62). maximum stress in turn is given by the As the value of p is usually between 2 and formula 3, the strain rate decreases with increasing 2n+1 Mh (3-65) strain, that is with increasing time. For this n 61 reason materials whose creep behavior can where M is the applied moment and I the be expressed by Equation (3-63) are often moment of inertia of the cross section. referred to as strain-hardening materials.

It the case of linear creep or linear elas- Again, tivs creep law is more reliable in ticity applications in which the load hicreases than , 2y h (3-66) in which it decreases. S...=M h, 21 (3-67) 3-8.3. Stress Distribution Accompanying The stress distribution is linear only when Creep. The presence of creep -'hange- the creep deformations are absent, or when they stress distribution in a structure from the are governed by a linear law as is the case one calculated from the linear theory of elas- with some high polymers. With metals the ticity.

The only exception to this statement final stress distribution is non-linear since is the stress (li:itribution accompanying linear the creep law is non-ln,ar. ( 52 .