The information in this User’s Manual has been carefully reviewed and is believed to be accurate. The vendor assumes no responsibility for any inaccuracies that may be contained in this document, makes no commitment to update or to keep current the information in this manual, or to notify any person or organization of the updates. The manufacturer reserves the right to make changes to the product described in this manual at any time and without notice. This product, including software, if any, and documentation may not, in whole or in part, be copied, photocopied, reproduced, translated or reduced to any medium or machine without prior written consent.

IN NO EVENT WILL THE MANUFACTURER BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN PARTICULAR, THE VENDOR SHALL NOT HAVE LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH HARDWARE, SOFTWARE, OR DATA. Any disputes arising between manufacturer and customer shall be governed by the laws of Santa Clara County in the State of California, USA.

The State of California, County of Santa Clara shall be the exclusive venue for the resolution of any such disputes. The manufacturer's total liability for all claims will not exceed the price paid for the hardware product. Manual Revision 1.0 Release Date: May 30, 2006 Unless you request and receive written permission from the manufacturer, you may not copy any part of this document. Information in this document is subject to change without notice. Other products and companies referred to herein are trademarks or registered trademarks of their respective companies or mark holders. Copyright © 2006 All rights reserved. Printed in the United States of America

Page 2

Preface Preface About This Manual This manual is written for system integrators, PC technicians and knowledgeable PC users. It provides information for the installation and use of the H8SSL-R10 motherboard. The H8SSL-R10 is based on the ServerWorks HT-1000 chipset and supports a single AMD Opteron 100 series processor in a 939-pin mi- croPGA ZIF socket and up to 4 GB of unbuffered ECC DDR400/333 SDRAM. Please refer to the serverboard speciﬁ cations pages on our web site for updates on supported processors. This product is intended to be professionally installed.

Manual Organization Chapter 1 includes a checklist of what should be included in your motherboard box, describes the features, speciﬁ cations and performance of the motherboard and provides detailed information about the chipset. Chapter 2 begins with instructions on handling static-sensitive devices. Read this chapter when installing the processor and memory modules and when installing the motherboard in a chassis. Also refer to this chapter to connect the ﬂ oppy and hard disk drives, the serial ports, the mouse and keyboard and the twisted wires for the power and reset buttons and the system LEDs.

If you encounter any problems, see Chapter 3 , which describes troubleshooting procedures for the video, the memory and the setup conﬁ guration stored in CMOS. For quick reference, a general FAQ (Frequently Asked Questions) section is pro- vided. Instructions are also included for contacting technical support. In addition, you can visit our web site for more detailed information. Chapter 4 includes an introduction to BIOS and provides detailed information on running the CMOS Setup utility. Appendix A provides BIOS Error Beep Code Messages. Appendix B lists BIOS POST Checkpoint Codes. iii

Page 3

H8SSL-R10 User’s Manual Table of Contents Preface About This Manual ...................................................................................................... iii Manual Organization ................................................................................................... iii Chapter 1: Introduction 1-1 Overview ......................................................................................................... 1-1 Checklist .................................................................................................... 1-1 H8SSL-R10 Image ...................................................................................

1-3 H8SSL-R10 Motherboard Layout ............................................................. 1-4 H8SSL-R10 Quick Reference ................................................................... 1-5 Serverboard Features .............................................................................. 1-6 ServerWorks HT-1000 Chipset: System Block Diagram .......................... 1-8 1-2 Chipset Overview ........................................................................................... 1-9 1-3 PC Health Monitoring ...................................................................................

1-10 1-4 Power Conﬁ guration Settings ....................................................................... 1-11 1-5 Power Supply ............................................................................................... 1-12 1-6 Super I/O ....................................................................................................... 1-13 Chapter 2: Installation 2-1 Static-Sensitive Devices ................................................................................. 2-1 2-2 Processor and Heatsink Installation ...............................................................

2-2 2-3 Mounting the Serverboard into a Chassis ...................................................... 2-4 2-4 Installing Memory ........................................................................................... 2-4 2-5 I/O Port and Control Panel Connections ........................................................ 2-6 2-6 Connecting Cables ......................................................................................... 2-7 Primary ATX Power Connector ............................................................... 2-7 Secondary Power Connector ....................................................................

2-7 NMI Button ................................................................................................ 2-7 Power LED ............................................................................................... 2-7 HDD LED ................................................................................................. 2-8 NIC1 LED ................................................................................................. 2-8 NIC2 LED ................................................................................................. 2-8 Overheat/Fan Fail LED ............................................................................

2-8 Power Fail LED ........................................................................................ 2-8 Reset Button ............................................................................................ 2-9 Power Button ............................................................................................ 2-9 iv

Page 4