ADP485 01 Eng 051209 (EN)

ADP485-01

Vibration/Shock resistance International Standard: IEC1131-2, IEC 68-2-6 （ TEST Fc ） / IEC1131-2 & IEC 68-2-27 (TEST Ea) COM1-DB9 female PIN Definition RJ12-VFD PIN Definition COM2-DB9 male PIN Definition RJ12-ADP485 PIN Definition In all RS-485 installations, the cable must be correctly terminated with two sets of resistors, one set at each end of the network (4,000 feet maximum total cable length). This applies even if you are only using one slave node connected to one master device. The terminating resistors prevent reflection problems that can interfere with data transmission. The resistance value of the terminating resistors should match the characteristic impedance of the cable.

A typical value is 120 ohms. The terminating 1 RS485- 1 +15V 2 RS485+ 2 GND 4 RS485- 4 SG+ 5, 6: Reserved 3, 6 RS485- 3 RS-485+ 4 RS-485- 5, 9 GND 5 GND resistors must be placed at the two farthest ends of the RS-485 network, regardless of where the master device is. In some cases master device RS-485 ports have built in or optional terminating resistors. Beware of your network (whether it has one node or 32 nodes) having only two sets of DB9 male Mini DIN Operation 0 ℃ ~55 ℃ (Temperature), 50~95%(Humidity), pollutant degree 2 3 RS485+ 3 SG- 1, 2, 6: NC 8 1 3 6 Storage -25 ℃ ~70 ℃ (Temperature), 5~95% （ Humidity ） Termination Resistor Switch 5, 6, 7, 8, 9: NC 1, 2, 4, 7:

NC 1 2 3 4 5 6 7 8 9 ADPCAB03B RS485 - RS485 + GND „ COM1, COM2, and RJ12 PIN Explanation: 8 RS485+ DB9 male 1394 male „ Environmental Specification „ Use of Terminating Resistance 2 4 RS485 - 1 3 5 6 6 7 8 9 4 3 6 7 8 9 terminating resistors.

„ Cable Connection ADPCAB03A 1 2 3 4 5 6 7 8 9 RS485 + GND 1 2 3 4 5 5 2 1 3 RS-485 Network Connection with Delta Products RS-485 network F1 F2 F3 COM1 COM2 one by one wiring HMI DOP Series connect to COM 1 Connecting cable (ADPCAB03A) Connecting cable (ADPCAB03B) DB9 male connector DB9 male connector RS-485 network RS-485 network RS-485 network „ ADP485-01 Щ VFD (AC Motor Drive) RJ12 „ ADP485-01 Щ ASD-A (Servo Drive) „ ADP485-01 Щ ASD-B (Servo Drive) „ ADP485-01 Щ DOP (HMI) http://www.delta.com.tw/industrialautomation/ 5011638900-DFE0 ADP485-01 is an OPEN-TYPE.

Please place the module in an enclosure away from airborne dust or high humidity and prevent electric shock or sudden shock on ADP485-01. Also, it is equipped with protective method such as some special tool or key to open the enclosure, so as to avoid the hazard to users or any damage to the module. Do NOT touch terminals when power on. When many devices are connecting in serial, their Baud rate and communication format setting should be the same. Also, each device must have individual Unit Address. I/O terminal screw should be tightened between 1.95 kg-cm (1.7 in-lbs). Use copper conductor only, 60 / 75 o C. „ ADP485-01 is mainly designed to connect Delta product by RS-485 interface.

It is equipped with surge absorber and limited current protection to ensure safe connection of different devices. Also, 120 Ω terminating resistance selection is available. This module enables Delta products to connect one another by RS-485 interface with much concern of safety and wide application. „ ADP485 offers four different connectors to enable the network connection for Delta’s PLC DVP series, HMI DOP series, AC Motor Drive VFD series and Servo drive ASD series. Production plant (Taoyuan) 2005-11-10 ADP485-01 Instruction Sheet Production series Production week Production year (2005) 1. Mounting plate 5. ON/OFF of terminating resistor (factory setting: OFF) Production Model 6 8 7 2.

COM1 (DB9 female) 6. DIN rail (35mm) z ADPCAB03B ADP485-01 Щ ASD-B connecting cable/30 cm 106,8 3. COM2 (DB9 male) 7. RS-485 port z ADPCAB03A ADP485-01 Щ ASD-A connecting cable/30 cm ADP48501T 5 280001 2 INTRODUCTION 90 3,4 4. Nameplate 8. RJ12 1 WARNING Serial number: 32 6 60 Unit: mm ADP485 - 01 Type 01 1 2 3 4 5 „ Optional Connecting Cable Product name RS-485 communication „ Product Profile: 3 „ Nameplate ： Model name: Operation 0℃~55℃(Temperature), 50~95%(Humidity), pollutant degree 2 Storage -25℃~70℃(Temperature), 5~95%（Humidity） Vibration/Shock resistance International Standard:

IEC1131-2, IEC 68-2-6（TEST Fc）/ IEC1131-2 & IEC 68-2-27 (TEST Ea) PIN 1 Definition RS485- 2 3 RS485+ RS485+ 4 RS485- 5, 6, 7, 8, 9: NC PIN 1 Definition +15V 2 3 GND SG- 4 SG+ 5, 6: Reserved PIN 3, 6 Definition RS485- 8 RS485+ 5, 9 GND 1, 2, 4, 7: NC PIN 3 Definition RS-485+ 4 RS-485- 5 GND 1, 2, 6: NC 5 4 3 2 1 9 8 7 6 1 2 3 4 5 90 106,8 6 7 8

Стр. 1