Hitachi Hydraulic Excavator Manual (EN)

T03-06-01to16.pdf

Technical Manual Operational Principle 650LC - 3 670LCH - 3 Hydraulic Excavator This Service Manual consists of three separate parts: Technical Manual (Operational Principle) Part No. TO1J7-E-00 Technical Manual (Troubleshooting) Part No. TT1J7-E-00 Workshop Manual (Workshop Manual in English only) Part No. W1J7-E-00 TO1J7-E-00 PART NO. ZAXIS 650LC -3 670LCH -3 HYDRAULIC EXCAVATOR TECHNICAL MANUAL OPERATIONAL PRINCIPLE TO1J7-E-00 PRINTED IN EUROPE (YC) 2006.03 Hitachi Construction Machinery www.hitachi-c-m.com PART NO. TO1J7-E-00

Стр. 1

T03-06-01to16.pdf

INTRODUCTION TO THE READER This manual is written for an experienced technician to provide technical information needed to maintain and repair this machine. If you have any questions or comments, at if you found any errors regarding the contents of this manual, please contact using “Service Manual Revision Request Form” at the end of this man- ual. (Note: Do not tear off the form. Copy it for us- age.): Publications Marketing & Product Support Hitachi Construction Machinery Co. Ltd. TEL: 81-298-32-7173 FAX: 81-298-31-1162 ADDITIONAL REFERENCES Be sure to thoroughly read this manual for cor- rect product information and service procedures.

Please refer to the materials listed below in addition to this manual. Operation Manual of the Engine Parts Catalog of the Engine Hitachi Training Material MANUAL COMPOSITION The Operator’s Manual The Parts Catalog This manual consists of three portions: the Techni- cal Manual (Operational Principle), the Technical Manual (Troubleshooting) and the Workshop Man- ual. Information included in the Technical Manual (Troubleshooting): technical information needed for operational per- formance tests, and troubleshooting procedures. Information included in the Workshop Manual:

technical information needed for maintenance and repair of the machine, tools and devices needed for maintenance and repair, maintenance standards, and removal/installation and assem- ble/disassemble procedures. PAGE NUMBER Information included in the Technical Manual (Operational Principle): technical information needed for redelivery and delivery, operation and activation of all devices and systems. Each page has a number, located on the center lower part of the page, and each number contains the following information: Example : T 1-3-5 Consecutive Page Number for Each Group Group Number Section Number T: Technical Manual W: Workshop Manual IN-01

Стр. 2

T03-06-01to16.pdf

INTRODUCTION SAFETY ALERT SYMBOL AND HEADLINE NOTATIONS In this manual, the following safety alert symbol and signal words are used to alert the reader to the potential for personal injury of machine damage. CAUTION: Indicated potentially hazardous situation which could, if not avoided, result in personal injury or death. This is the safety alert symbol. When you see this symbol, be alert to the potential for personal injury. Never fail to follow the safety instructions prescribed along with the safety alert symbol. The safety alert symbol is also used to draw attention to component/part weights.

To avoid injury and damage, be sure to use appropri- ate lifting techniques and equipment when lifting heavy parts. IMPORTANT: Indicates a situation which, if not conformed to the instructions, could result in damage to the machine. NOTE: Indicates supplementary technical information or know-how. UNITS USED Example : 24.5 MPa (250 kgf/cm 2 , 3560 psi) A table for conversion from SI units to other system units is shown below for reference purposees. SI Units (International System of Units) are used in this manual. MKSA system units and English units are also indicated in parenthheses just behind SI units.

IN-02 Quantity To Convert From Into Multiply By Quantity To Convert From Into Multiply By Length mm in 0.03937 Pressure MPa kgf/cm2 10.197 mm ft 0.003281 MPa psi 145.0 Volume L US gal 0.2642 Power kW PS 1.360 L US qt 1.057 kW HP 1.341 m3 yd3 1.308 Temperature °C °F °C×1.8+32 Weight kg lb 2.205 Velocity km/h mph 0.6214 Force N kgf 0.10197 min-1 rpm 1.0 N lbf 0.2248 Flow rate L/min US gpm 0.2642 Torque N⋅m kgf⋅m 1.0197 mL/rev cc/rev 1.0 N⋅m lbf⋅ft 0.7375

Стр. 3

T03-06-01to16.pdf

SECTION 1 GENERAL SECTION AND GROUP CONTENTS Group 1 Specification Group 2 Component Layout Group 3 Component Specifications SECTION 2 SYSTEM Group 1 Control System Group 2 Control System Group 3 ECM System Group 4 Hydraulic System Group 5 Electrical System SECTION 3 COMPONENT OPERATION TECHNICAL MANUAL (Operational Principle) Group 1 Pump Device Group 2 Swing Device Group 3 Control Valve Group 4 Pilot Valve Group 5 Travel Device Group 6 Signal Control Valve Group 7 Others (Upperstructure) Group 8 Others (Undercarriage) TECHNICAL MANUAL (Troubleshooting) SECTION 4 OPERATIONAL PER- FORMANCE TEST Group 1 Introduction Group 2 Standard Group 3 Engine Test Group 4 Excavator Test Group 5 Component Test SECTION 5 TROUBLESHOOTING All information, illustrations and speci- fications in this manual are based on the latest product information available at the time of publication.

The right is reserved to make changes at any time without notice. Group 1 Diagnosing Procedure Group 2 Monitor Unit Group 3 Dr. ZX Group 4 e-Shovel Group 5 Component Layout Group 6 Troubleshooting A Group 7 Troubleshooting B Group 8 Electrical System Inspection Hitachi Construction Machinery Co., Ltd. COPYRIGHT(C)2006 Tokyo, Japan All rights reserved

Стр. 4