Электропривод багажника Geely Coolray — инструкция по установке (EN)

 If the key fob has a tailgate open button, press this button for 3s to open and close the tailgate. If don’t have, you need to press the unlock button 3 ELECTRIC TAILGATE FOR GEELY COOLRAY WITH UPPER LATCH 19+ 吉利缤越上吸 times to open and close the tailgate. Installation Instruction unplugging. Wiring Diagram  For safety and to ensure the normal use of the product, please install it by a professional installer. Do not disassemble the machine without  Before installing the product, start the engine first, check the function display of the car dashboard, the operation of the buttons in the car is normal, and the surface of the car is not scratched.

If you have any  Check whether the tailgate opens and closed normally, check whether the  Installer should first remove the metal objects and other hard objects on their bodies to prevent damage to the car seat or interior during  During the installation process, the removed automobile components should be put away to avoid scratching the instrument panel in the car. Debris left in the wiring should be disposed of in time and not left in the  According to our wiring method, avoid affecting the moving parts of the car during the wiring process, such as the steering wheel drive shaft, accelerator and brake pedal and other vehicle control prats.

Each wiring harness needs to be fixed after being routed to prevent it from coming  Please connect each wiring harness according to our wiring method (Noted  Do not insert or remove the connected plug while the power is on, otherwise the host or accessories may be damaged during plugging and permission to avoid damage to the machine and accident. car. The joint must be insulated to prevent short circuit. questions, please report to car owner in time.  Turn off the engine and prepare related tools. the position of the ground wire). Installation Precautions lights are normal. installation. loose.

Стр. 1

3. Remove the left and right side panels 4. Remove panel 6. Remove original 1. Car appearance 2. 5. Pry open the gas spring snap ring, and remove the left and right side poles 1. Car appearance 2. Remove the middle panel 3. Remove the left and right side panels 4. Remove the large tailgate trim panel 5. Pry open the gas spring snap ring, and remove the left and right side poles 6. Remove the screw ball of the original car body and install our screw ball (same for left and right) 7. Remove the taillight trim panel 8. Remove the original tailgate screw ball and taillight screw, use our screws to install the bracket, ("L" left and "R right") 9. Install the poles ("L" is left, "R is right") 10.

Remove the rubber plug of the original car, insert the brace wire into the hole,(same left and right) 11. Unplug the original car lock cable and connect with our cable 12. Our white wire is connected to the original car tail door button signal wire (black and blue border)

Стр. 2

15. Remove the trim panel in the main driving diagram 16. box 17. OBD docking 18. Drill 13. Remove the original car lock and install our lock 14. 13. Remove the original car lock and install our lock 14. Location of GND 15. Remove the trim panel in the main driving diagram 16. Take normal power in the fuse box 17. OBD docking 18. Drill holes in the main driving panel to install the front button 19. Pass the wiring harness of the connection control box into the corrugated pipe 20. Wiring diagram (red: power cord, blue: front button line, yellow: OBD) 21. Punch holes in the tailgate trim panel to install the rear button 22.

Connect the corresponding line to the control box, and fix the control box in a suitable position 23. Reset all trim panels. After installation is complete, close the door manually to initialize the system

Стр. 3

After turning on, the door must be closed manually and the function can be used normally. Note: Do not use screwdriver or other tools to lock the secondary lock as a door closing, otherwise a series of problems such as abnormal door opening and closing. (1) Remote control door opening and closing: Press the remote control unlock key 3 times (some models press the trunk key for a long time) to control the trunk. Note: When pressing the unlock key, press 3 times at a constant speed within 4 seconds. (2) The original driver of the trunk picks the key: Control the opening and closing of the trunk. Note:

The control mode is the same as that before installation, and will not take effect until the vehicle is unlocked. (3) Front key/central control unlock key: Press the front key for about 15s to control the opening and closing of the trunk; If the front key is not installed, press the central control unlock key of the original car 3 times to control the opening and closing of the trunk. Note: The function of opening the trunk by the front key will only take effect in the state of flameout or P Function Description Control mode of door opening and closing After then installation is completed, you must set the tailgate learning. Make sure that the door can be opened and closed in place.

(Raise the tailgate to ideal height. Then press the tailgate button for 3‐5 seconds. You will hear a sound “ Deep ——” and then loose your hand. Press the tailgate button again and close it. You will hear a sound again “ Deep ” . Tail gate learning is finished. When the tailgate cannot be opened normally, find the original car emergency safety lock in the trunk, open the emergency cover and pull the emergency switch to open. After the installation is completed, please check: 1. Are all screws replaced with special screws? 2. Is the socket inserted? 3. Does the electric suction lock work? 4. 5. tailgate.

Check the points before the trim panel is restored Function Description After turning on, the door must be closed manually and the function can be used normally. Note: Do not use screwdriver or other tools to lock the secondary lock as a door closing, otherwise a series of problems such as abnormal door opening and closing. Control mode of door opening and closing (1) Remote control door opening and closing: Press the remote control unlock key 3 times (some models press the trunk key for a long time) to control the trunk. Note: When pressing the unlock key, press 3 times at a constant speed within 4 seconds. (2) The original driver of the trunk picks the key:

Control the opening and closing of the trunk. Note: The control mode is the same as that before installation, and will not take effect until the vehicle is unlocked. (3) Front key/central control unlock key: Press the front key for about 15s to control the opening and closing of the trunk; If the front key is not installed, press the central control unlock key of the original car 3 times to control the opening and closing of the trunk. Note: The function of opening the trunk by the front key will only take effect in the state of flameout or P gear, and the function of closing the trunk will take effect at any time.

The functions of opening and closing the trunk by the central control unlock key will only take effect under the flameout state. (4) Trunk rear button: Press to control the trunk to close. Anti-pinch function In the process of opening and closing the door, if obstructions are encountered, the trunk will immediately stop to avoid accidents.

Стр. 4