MIL-STD-1808C System Subsystem Sub-Subsystem Numbering Standard Manual PDF (EN)

Downloaded from https://www.everyspec.com NOT MEASUREMENT SENSITIVE MIL-STD-1808C w/CHANGE 1 2 September 2016 SUPERSEDING MIL-STD-1808C 24 January 2014 DEPARTMENT OF DEFENSE INTERFACE STANDARD SYSTEM SUBSYSTEM SUB-SUBSYSTEM NUMBERING AMSC N/A AREA TMSS

Стр. 1

Downloaded from https://www.everyspec.com MIL-STD-1808C w/CHANGE 1 FOREWORD 1. This standard is approved for use by the Department of the Air Force and is available for use by all Departments and Agencies of the Department of Defense. 2. In order to provide standardization between publications a standardized numbering system has been developed. It is designed with sufficient flexibility to permit expansion and application outside the technical manual system to support logistics elements that interact with or directly influence equipment maintenance and technical manual development and use. 3. To ensure maximum flexibility, gaps have been left in the system and subsystem numbering sequences.

Manufacturers are encouraged to use the unassigned systems and subsystems to accommodate unique design or emerging technologies when required, as approved by the procuring activity and current acquisition policy. Please provide any changes to the Air Force Technical Manual Specifications and Standards (TMSS) office at the address in step 6 below. 4. As a minimum, this standard is intended to be used in conjunction with MIL-DTL-83495 and MIL-HDBK-863. Additional applications are available as defined in the documents identified in section 2 . 5. The purpose of change 1 is to add a statement describing the proper procedure for requesting use of the unassigned SSSN numbers.

Change 1 also designates chapter 19 to training and chapter 20 to equipment storage, aligning the MIL-STD-1808 with the MIL-DTL-83495. 6. Comments, suggestions, or questions on this document should be addressed to AFLCMC/HIAM Technical Data Section, 4170 Hebble Creek Road, Bldg. 280, Door 15, Area A, Wright-Patterson AFB, OH 45433–5653 or emailed to SGMLsupport@us.af mil . Since contact information can change, the currency of this address information should be verified using the ASSIST Online database at https://assist.dla mil/. ii

Стр. 2

Downloaded from https://www.everyspec.com MIL-STD-1808C w/CHANGE 1 CONTENTS FOREWORD.................................................................................................................................................................

ii 1 SCOPE........................................................................................................................................................................1 1.1 Scope........................................................................................................................................................................1 1.2 Acquisition applicability.........................................................................................................................................1 2 APPLICABLE DOCUMENTS .................................................................................................................................1 2.1 General.....................................................................................................................................................................1 2.2 Government documents ..........................................................................................................................................1 2.2.1 Specifications, standards and handbooks...........................................................................................................1 2.2.2 Other government documents, drawings and publications..............................................................................1 2.3 Order of precedence...............................................................................................................................................1 3 DEFINITIONS............................................................................................................................................................1 3.1 Definitions................................................................................................................................................................1 4 GENERAL REQUIREMENTS.................................................................................................................................2 4.1 System Subsystem Sub-subsystem Number (SSSN)...........................................................................................2 4.1.1 Number composition............................................................................................................................................2 4.1.1 Typical system subsystem sub-subsystem number composition .....................................................................3 5 DETAIL REQUIREMENTS.

....................................................................................................................................3 5.1 Use of SSSN ..........................................................................................................................................................3 5.2 System numbering ..................................................................................................................................................3 5.2.1 01 THRU 04........................................................................................................................................................3 6 NOTES....................................................................................................................................................................108 6.1 Intended Use .......................................................................................................................................................108 6.2 Acquisition requirements....................................................................................................................................108 6.3 Tailoring guidance ..............................................................................................................................................108 6.4 Subject (keyword) list........................................................................................................................................108 6.5 Change notation ..................................................................................................................................................108 INDEX........................................................................................................................................................................109 CONCLUDING MATERIAL....................................................................................................................................113 iii

Стр. 3

Downloaded from https://www.everyspec.com MIL-STD-1808C w/CHANGE 1 1 SCOPE 1.1 Scope. This standard sets forth requirements for the system, subsystem, and sub-subsystem numbering requirements for engineering drawings, technical manuals, and other acquisition and logistics support requirements for aircraft, missile and space systems, engines, and ground communication-electronic equipment. Additionally, it may be used for supportability analysis, configuration management, maintenance data collection, or wherever a consistent maintainability related reference numbering requirement exists across a weapon system. 1.2 Acquisition applicability.

This standard will be used by all Air Force acquiring activities and their respective contractors during the development and acquisition of weapon systems and equipment. 2 APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 , 4 , and 5 of this standard. This section does not include documents cited in other sections of this standard or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements documents cited in sections 3 , 4 , and 5 of this standard, whether or not they are listed.

2.2 Government documents. 2.2.1 Specifications, standards and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-DTL-9854 Technical Manuals:

Structural Repair (Aircraft) MIL-DTL-38807 Technical Manuals - Illustrated Parts Breakdown MIL-DTL-83495 Technical Manuals - On Equipment Maintenance Manual Set MIL-DTL-87268 Manuals, Interactive Electronic Technical - General Content, Style, Format, and User-Interaction Requirements (Copies of federal and military specifications, standards and handbooks are available at http://quicksearch.dla.mil/ or from the Standardization Documents Order Desk, Building 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094.) 2.2.2 Other government documents, drawings and publications.

The following other Government documents, drawings, and publications form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. U.S. AIR FORCE TECHNICAL MANUALS TO 1-1-8 Exterior Finishes, Insignia, and Marks Applicable to United States Air Force Aircraft (Copies of these documents required by users with " mil" government web address access are available online at https://www my.af mil/etims/ETIMS/index.jsp . Refer to helpdesk information if obtaining copies without a TO subscription account.

Copies of documents required by contractors in connection with specific procurement functions should be obtained from the acquiring activity or as directed by the contracting officer.) 2.3 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3 DEFINITIONS 3.1 Definitions. Definitions will be in accordance with the documents listed in section 2 . 1

Стр. 4