HOME INSTALLATION When servicing the fuel system, do not smoke or allow open flame or sparks in the vicinity. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00330a) 1. Position the fuel tank in the frame and position the fuel tank mounting bracket to the frame. 2. See Figure 4-2 . Loosely thread in the two mounting bolts and washers through the forward holes of the bracket into the threaded boss on the frame. 12. Lift fuel pump/filter/fuel level sensor assembly out of the fuel tank. 3. Tighten the mounting bolts to 40-48 Nm (30-35 ft-lbs). 13. Cover fuel tank opening or drain fuel tank as required. 4.
Connect the fuel module connector while supporting the top plate connector half with the opposite hand. 14. Remove rear wheel and swingarm. See 2.26 REAR WHEEL and 2.38 SWINGARM . 5. See Figure 4-1 . Install the smaller return line and the larger pressure line while supporting the mating port. Press the lines on until the click is heard that indicates engagement. 15. Remove passenger pillion and rear fender. 16. Remove the two fasteners fastening the mud flap plate at rear of voltage regulator. Remove the mud flap by pinching side tabs to disengage from seat pan. 6. Attach the larger pressure line and the smaller return line to the fuel rail. 7.
Press on the vapor vent hose while supporting the mating port with the opposite hand. 17. Remove fuel cap and fuel filler boot. Replace fuel cap. 18. At the fuel rail, disconnect the larger pressure fuel line and the smaller return fuel line by pressing blue buttons with thumb and first finger.Then disconnect both fuel lines from the fuel tank top plate. 8. Install mud flap and stud plate. 9. Install rear fender and passenger pillion. 19. Use opposite thumbs to push the vapor vent hose off of the outlet tube. 10. Install swingarm. See 2.38 SWINGARM . 11. Install the rear wheel assembly and adjust the drive belt tension. See 2.26 REAR WHEEL . 20.
Unbolt the two bolts and their washers on the bracket that holds the fuel tank against the frame. 12. Fuel the motorcycle as required. Replace the fuel cap. 21. Remove fuel tank from motorcycle. 13. Install air box. See 1.5 AIR CLEANER AND EXHAUST SYSTEM . 22. If the fuel tank is going to be stored prior to service, either drain using a siphon or cap the pressure fuel port, the return fuel port, and the vapor vent port on the fuel tank top plate. 14. Connect negative battery cable. 15. Install air box cover by positioning the air box cover with the locating pins in the holes on the frame tabs. Turn bailhead fastener 1/4 turn clockwise. CLEANING AND INSPECTING 1. Drain the fuel tank.
Use a common pump or siphon and an approved gasoline storage container of sufficient capacity. 16. Close seat. 17. Install main fuse and side cover. 2. Remove fuel pump/filter/fuel level sensor assembly from tank. 18. Check fuel system pressure. See 4.13 FUEL PRESSURE TEST . 3. Clean the tank interior with commercial cleaning solvent sm01205 or a soap and water solution. Shake the tank to agitate the cleaning agent. 4. Flush the tank thoroughly after cleaning and allow it to air dry. 3 2 When servicing the fuel system, do not smoke or allow open flame or sparks in the vicinity. Gasoline is extremely 1 flammable and highly explosive, which could result in death or serious injury. (00330a) 5.
Inspect the evaporative emissions system vapor valve line and pressure and return fuel lines for cuts, cracks or holes. 1. Mounting bolt Replace lines as needed. 2. Washer 6. Inspect the tank for leaks and other damage. If damaged, 3. Hole replace it. Figure 4-2. Fuel Tank Mounting Bracket (typical) 2009 VRSC Service: Fuel System 4-5 0330a) emissions system vapor valve line fuel lines for cuts, cracks or holes. 1. Mounting bolt d. 2. Washer ks and other damage. If damaged, 3. Hole Figure 4-2. Fuel Tank Mounti 2009 VRSC Se ng Bracket (typical) rvice: Fuel System 4-5