HOME 5. Mate connector [24] halves. 6. the grip sleeve was removed, thoroughly clean handlebar to remove all adhesive residue. Pour adhesive into new grip. Roll grip to evenly distribute adhesive on inside sur- faces. Install grip on handlebar with a twisting motion. 1. See Figure 7-75 . From inside the switch housing, remove the screw with lockwasher (4) to release the bracket (5). Remove bracket and switch assembly from the housing. 2. Move cable conduit (3) from beneath wing of bracket. Cut wires 6.4 mm (0.25 in. ) from old switches (1, 2). Discard old switch and bracket assembly. 7. See Figure 7-73 . Install upper and lower switch housings on handlebar.
Be sure that ribs (2) on outboard side of switch housings fit in grooves (3) molded into grip. 3. Slide conduit forward over cut ends of switch wires and cut off 12.7 mm (0.5 in.) of conduit (3) material. Push conduit back to access switch wires. 8. Verify that the wire harness conduit runs in the groove at the bottom of the handlebar. Be sure that the upper switch housing harness will not be pinched under the handlebar when the switch housing screws are tightened. 4. Separate the new horn switch (1) and high/low beam switch (2) wires into two bundles. 9. Start the upper and lower switch housing screws, but do not tighten.
NOTE Replacement high/low beam switch and horn switch wires are cut to length of 63.5 mm (2.5 in.) and 50.8 mm (2.0 in.) respectively, and partially stripped. 10. See Figure 7-74 . Position the clutch hand lever assembly inboard of the switch housing assembly, engaging the tab (3) on the lower switch housing in the groove (2) at the bottom of the clutch lever bracket. 5. See 7.29 HANDLEBAR SWITCH ASSEMBLIES for information on splicing and general repair practices. 11. Align the holes in the handlebar clamp with those in the clutch lever bracket and start the two screws (with flat washers). Position for rider comfort.
Beginning with the top screw, tighten screws to 6.8-9.0 Nm (60-80 in-lbs ) using a T27 TORX drive head. 6. Loop switch wires so that spliced lengths are positioned as shown in Figure 7-76 . Route wires downstream of splices beneath wing on high/low beam switch side of bracket as shown in Figure 7-75 . 7. See Figure 7-76 . Install a new 177.8 mm (7.0 in.) cable strap (5) beneath wing on horn switch side (1) of bracket and capture wire splices (4). 12. Using a T25 TORX drive head, tighten lower and upper 8. Place switch assembly into upper housing aligning hole in bracket with threaded hole in boss. Be sure that bracket is fully seated.
The step at the edge of the boss captures the bottom edge of the bracket, while tabs on each side of the bracket fit in slots cast into the housing. 9. See Figure 7-75 . Install screw and lockwasher (4) to secure bracket (5) inside housing. Verify that wing on high/low switch (2) side of bracket captures edge of conduit (3) as shown. Be sure that all lights and switches operate properly before operating motorcycle. Low visibility of rider can result in death or serious injury. (00316a) 13. Replace the maxi-fuse. and the right side cover. 10. Securely tighten cable strap to draw splices to bracket. Remove any excess cable strap material. 14. Replace the left side cover. 11.
Continue with 7.31 LEFT HANDLEBAR SWITCH, 15. Test the switches for proper operation. Assembly . DISASSEMBLY 1. Using a T25 TORX drive head, remove the upper and lower switch housing screws. 2. If replacing lower housing switches, perform next step before continuing to repair section. If replacing upper housing switches, proceed directly to repair section. 3. Using a T27 TORX drive head, loosen the upper screw securing the handlebar clamp to the clutch lever bracket. Remove the lower clamp screw with flat washer. switch housing screws to 4.0-5.1 Nm (35-45 in-lb NOTE Always tighten the lower switch housing screw first so t gap between the upper and lower housings is at the f the switch.
35-45 in-lb SWITCH REPAIR/RE PLACEMENT air NOTE high/low beam switch as a single witch is determined to be faulty. Electrical Upper Housing Rep Replace the horn switch and assembly even if only one s 7-56 2009 VRSC Service: