Section 05 ELECTRICAL SYSTEM Subsection 07 (GAUGE) Double click the iS button to move the suspen- sion to the up position. If the suspension does not move to the up position, the problem is related to the electrical power system. Refer to POWER DISTRIBUTION subsection. If the suspension moves to the up position, test the 3 A GAUGE fuse (fuse 1) in fuse box 1 (FB1). If the GAUGE fuse tests good, carry out an IN- FORMATION CENTER INPUT VOLTAGE TEST. If the information center input voltage test is good, test for continuity of the gauge ground circuit (gauge connector pin 11 (BLACK wire) to the ground bus-bar (pin E12) in FB2. Refer to WIRING DIAGRAM for circuit details.
Carry out a continuity check of the CAN bus wires from the CAN bus-bars in FB2 to the information center (pins 2 and 3). Refer to the WIRING DIA- GRAM for more details. If an open circuit is detected, carry out same test from the 12 pin steering connector (C01 pins 8 and 9). All Indications ON Except for: No LAKE WATER TEMP indication No VTS indication No iBR position indication CHECK ENGINE light is on. The iBR CAN bus circuit is open or the iBR module is at fault. NOTE: The ECM will generate several fault codes and engage LIMP HOME mode. Carry out a continuity check of the CAN bus wires from the CAN bus-bars in FB2 to the iBR module (pins 2 and 3).
Refer to the WIRING DIAGRAM for more details. Information Center Turns ON with Some Indications Missing 1. Connect to the latest applicable B.U.D.S. soft- ware, refer to COMMUNICATION TOOLS AND B.U.D.S. SOFTWARE subsection. 2. Read the fault codes. If a fault code is related to a communication prob- lem, carry out a continuity test of the CAN bus wires between the applicable module and the CAN bus-bars in FB2. NOTE: The information center, ECM, iS module, iBR module, and the diagnostic connector are linked together through CAN bus-bars in fuse box 2. If one wire of the two wire CAN bus system is open, communication will be slower than nor- mal.
Multiple fault codes may be generated and the ECM will put the watercraft in LIMP HOME mode. If one module cannot be seen in B.U.D.S., the fault may be the wires that link the module to the CAN bus bars or internal to that module. Test the CAN bus wires from the faulty module to the bus-bars in FB2 for continuity before assuming the problem is the module. NO RPM Indication and NO Engine Hour Display If there is NO RPM indication and NO engine hour display, and the watercraft is in LIMP HOME mode, the CAN bus to the ECM is open. Carry out a continuity check of the CAN bus wires from the CAN bus-bars in FB2 to the ECM mod- ule, connector B pins C1 and C2 (B-C1 and B-C2).
Refer to the WIRING DIAGRAM for more details. NO iS Position Display If there is no iS position display (suspension posi- tion), the iS module is at fault, or its CAN bus cir- cuit is open. Carry out a continuity check of the CAN bus wires from the CAN bus-bars in FB2 to the iS module (pins 2 and 3). Refer to the WIRING DIAGRAM for more details. Information Center Goes Blank Except for: GPS indicator ON Compass ON (if watercraft moving) Fuel level ON iBR fault indicator light ON Indicated speed No other indications visible. There is no communication between the informa- tion center and all other modules (ECM, iS, iBR).
NO Fuel Level Indication If there is no fuel level indication, test the fuel level sensor and its wiring circuit to the infor- mation center. Refer to FUEL TANK AND FUEL PUMP subsection. NO Depth Gauge Indication If there is no depth gauge indication available and the depth sounder active indicator is not on, refer to DEPTH GAUGE in this subsection. smr2009-036 343