Bombardier Recreational Products Inc. (BRP) Sea-Doo RXT iS255 GTX LIMITED — Print Preview - C:\DOCUME~1\coderma\LOCALS~1\Temp\.aptcache\smr2009Piranhaen6/tfa03092

Section 06 STEERING AND PROPULSION Subsection 02 (iBR AND VTS) If battery voltage is not measured, check the fol- lowing: 30 A iBR fuse in FB2 Battery voltage at fuse contact D11 of FB2 Wire continuity pin 2 iBR 3 pin connector to D12 of FB2 Jumper continuity fuse contact FB2-D11 to FB2-A6 of 12 Vdc bus-bar. If voltage is good to the negative battery post but not to pin 1 of the connector (ground wire to en- gine), check for an open or bad ground wire (loose, corroded, or pitted terminals, wire continuity, etc.) If battery voltage measured is as specified, carry out same test using a 12 Vdc test light. Test light should be bright.

If test light is not bright to pin 1 only, look for a bad contact on the ground circuit (loose, corroded, pitted, etc.). If test light is not bright to the negative battery post, first check voltage at battery terminals to ensure battery is not discharged. If battery volt- age is good, look for a bad contact in the 12V iBR unswitched power circuit (loose, corroded, pitted, etc.). If un-switched 12 Vdc power to the iBR actuator is good, test for the switched 12 Vdc as per fol- lowing steps. 4. Briefly press the START/STOP button to wake the electrical system. NOTE: The 5 A switched power to the iBR actua- tor is for the iBR electronic module and BRLS.

If battery voltage is not measured at all, check the following: 5 A iBR control (CRTL) fuse in FB1 Battery voltage at fuse contact A4 of FB1 Wire continuity pin 1 iBR 12 pin connector to A3 of FB1 Jumper continuity fuse contact FB1-A4 to FB1-C2 of 12 Vdc accessory bus-bar. If voltage is good to the negative battery post but not to pin 1 of the connector (ground wire to engine), check for an open or bad ground wire (loose, corroded, or pitted terminals, wire conti- nuity, etc.). If battery voltage measured is as specified, carry out same test using a 12 Vdc test light. Test light should be bright.

If test light is not bright to pin 1 of the 3 pin con- nector, look for a bad contact on the ground circuit (loose, corroded, pitted, etc.). If test light is not bright to battery negative ter- minal, first check voltage at battery terminals to ensure battery is not discharged. If battery volt- age is good, look for a bad contact in the 12 V iBR switched power circuit (loose, corroded, pit- ted, etc.). If the iBR actuator input voltages and ground cir- cuit are good, and there is no CAN bus or BRLS fault, replace the iBR actuator. iBR Actuator Removal 1. Move the iBR gate to the forward position (full up) using the iBR OVERRIDE function.

Refer to SYSTEM DESCRIPTION (iBR) in this subsec- tion. Step 1: Press START/STOP button Step 2: Install D.E.S.S. key sdd2009-001-019_g 5. Measure for the switched input voltage to the iBR actuator as per following table. NOTICE Do not try to move the iBR gate by hand with the locking sleeve (iBR key) installed or component damage will occur. CAUTION Wait at least 5 minutes for wa- tercraft electrical power system to shut down before working in the iBR gate area. smr2009-037 391 iBR ACTUATOR INPUT VOLTAGE TEST (5 AMP SWITCHED) iBR CONNECTORS BATTERY READING 12 PIN 3 PIN Pin 1 Pin 1 - Battery voltage Pin 1 - Ground post