Bombardier Recreational Products Inc. (BRP) Sea-Doo RXT iS255 GTX LIMITED — Print Preview - C:\DOCUME~1\coderma\LOCALS~1\Temp\.aptcache\smr2009Piranhaen6/tfa03092

Section 06 STEERING AND PROPULSION Subsection 02 (iBR AND VTS) 7. Install remaining parts in the reverse order of removal, refer to appropriate procedure in this subsection. across the 4 the diodes (pin A to pin C). This 2.4 Vdc at pin B tells the gauge the VTS switch is open. If the VTS UP button is pressed, 2 diodes are by- passed by the closed switch. The remaining two diodes in the circuit drop 1.2 Vdc (at pin A). If the VTS DOWN button is pressed, 1 diode is by- passedby the closed switch. The remaining three diodes in the circuit drop 1.8 Vdc (at pin A).

The gauge senses these voltages through pin 13 of its connector, and interprets them as signals that tell it which is activated (VTS UP or VTS DOWN). Since the command generated by the closure of a VTS switch concerns the VTS module, a circuit within the gauge will translate it to CAN proto- col and transmit it through the CAN bus. The VTS module will react to the command, carry out the function, and transmit the result back through the CAN bus. The gauge will use the signals from the switches and the transmitted information from the other modules, convert them to an indication, and cancel the command signal it sent out once the function has been carried out. NOTE:

The above stated voltages vary slightly de- pending on the actual voltage applied to the circuit and the current flow through the diodes. When using a Fluke 115 multimeter for testing in diode test mode, the voltage and current applied by the multimeter are lower than in circuit. The quality of probe contact, the actual probes and leads, and the precision of the meter calibration will all affect the results, which will most likely be slightly lower than nominal values stated. Models With Plastic Retaining Tabs on Fitting Plate NOTE: Installation is the same as the model with metal retainer except for the following. 1. Insert the fitting plate through the outer plate. 2.

Push the fitting plate in until it bottoms out and the retaining tabs (x2) snap securely into posi- tion. NOTICE Ensure both tabs are properly locked to secure fitting plate to the support plate. If fitting plate is not properly locked in position, water may seep into the bilge. smr2009-043-008_b 1. Top fitting plate retaining tab (bottom tab similar) 3. Install remaining parts in the reverse order of removal, refer to appropriate procedure in this subsection. VTS Control Button Functional Test Using iBR OVERRIDE Function 1. Press the START/STOP button. 2. Install D.E.S.S. key to power up the electrical system. NOTE: Electrical power will shut off after approx- imately 3 minutes.

Briefly press the START/STOP button to reactivate the electrical system when re- quired. 3. Activate the iBR override function, refer to SYS- TEM DESCRIPTION (iBR) in this subsection. 4. Press and hold the VTS DOWN arrow button. The iBR gate and steering nozzle will move downwards together up to the full VTS down position. The iBR gate will then continue mov- ing to the full reverse/braking position alone. VTS CONTROL BUTTON VTS Button Overview The VTS button contain a series of 4 diodes for the UP and DOWN arrow switches. Refer to WIRING DIAGRAM. The center wire to the switches (pin C), is com- mon for iS button and VTS button (somewhat like a ground wire).

The other two wires (pins A and B), act as signal wires for each set of switches to the gauge. They actually each form one branch of an electronic circuit within the gauge. Each diode (in circuit) drops a nominal 0.6 Vdc when conducting electricity. If the circuit current passes through all four diodes (say VTS switch open), a drop of 2.4 Vdc would be measured smr2009-037 403