WTEC III ELECTRONIC CONTROLS TROUBLESHOOTING MANUAL H. ENGINE BRAKE ENABLE AND PRESELECT REQUEST PLUS ENGINE BRAKE ENABLE OUTPUT WITH SINGLE LEVEL COMPRESSION BRAKES USES: Used with engine brakes to signal the ECU that the brake is active and to provide increased braking by preselecting a lower range. Also prevents engagement of engine brake with throttle > 0 or lockup OFF. Figure P–12. Engine Brake Enable And Preselect Request Plus Engine Brake Enable Output With Single Level Compression Brakes P–12 Copyright © 2001 General Motors Corp. APPENDIX P — INPUT/OUTPUT FUNCTIONS WARNING!
These schematics show the intended use of the specified controls features which have been validated in the configuration shown. Any miswiring or use of these features which differs from that shown could result in damage to equipment or property, personal injury, or loss of life. ALLISON TRANSMISSION IS NOT LIABLE FOR THE CONSEQUENCES ASSOCIATED WITH MISWIRING OR UNINTENDED USE OF THESE FEATURES. VA VO RIABLES TO SPECIFY: Preselect range. Standard value is fourth range. CATIONS:
Various SWITCHED *ENGINE THROTTLE POWER SWITCH NC V D2 WIRE 132 E2 DASH BRAKE **ENGINE V-3 COM NO LIGHT ON BRAKE ENGINE BRAKE ENABLE OUPUT B1 OPTIONAL ECU CUSTOMER-FURNISHED VIM VIW CONNECTOR(S) Relay shown de-energized WIRE 169 *NOTE: This switch is part of the engine brake system and S-26 ENGINE BRAKE AND provides an indication when the engine is at closed throttle. S PRESELECT REQUEST ENGINE BRAKE T Rh Ei Cs Osw Mit Mch E, N o Dr Ean D e foq ru i av la l l ie nn stt a c llo an tit oro nl s f .eature, is DASH SWITCH WIRE 143H **NOTE:
The engine brake must provide a low engine speed S-32 SIGNAL RETURN shutoff feature, set to disable the brake at a speed slightly SEE NOTE ON INSTALLATION higher than idle rpm. DRAWING AS07-027 NOTE: If the engine brake solenoid is an inductive load, it must be diode suppressed. V07116 SWITCHED *ENGINE THROTTLE POWER SWITCH NC V D2 WIRE 132 E2 DASH BRAKE **ENGINE V-3 COM NO LIGHT ON BRAKE ENGINE BRAKE ENABLE OUPUT B1 OPTIONAL ECU CUSTOMER-FURNISHED VIM VIW CONNECTOR(S) Relay shown de-energized WIRE 169 *NOTE: This switch is part of the engine brake system and S-26 ENGINE BRAKE AND provides an indication when the engine is at closed throttle.
S PRESELECT REQUEST ENGINE BRAKE T Rh Ei Cs Osw Mit Mch E, N o Dr Ean D e foq ru i av la l l ie nn stt a c llo an tit oro nl s f .eature, is DASH SWITCH WIRE 143H **NOTE: The engine brake must provide a low engine speed S-32 SIGNAL RETURN shutoff feature, set to disable the brake at a speed slightly SEE NOTE ON INSTALLATION higher than idle rpm. DRAWING AS07-027 NOTE: If the engine brake solenoid is an inductive load, it must be diode suppressed. V07116 SWITCHED *ENGINE THROTTLE POWER SWITCH NC V D2 WIRE 132 E2 DASH BRAKE **ENGINE V-3 COM NO LIGHT ON BRAKE ENGINE BRAKE ENABLE OUPUT B1 OPTIONAL ECU CUSTOMER-FURNISHED VIM VIW CONNECTOR(S) Relay shown de-energized WIRE 169 *NOTE:
This switch is part of the engine brake system and S-26 ENGINE BRAKE AND provides an indication when the engine is at closed throttle. S PRESELECT REQUEST ENGINE BRAKE T Rh Ei Cs Osw Mit Mch E, N o Dr Ean D e foq ru i av la l l ie nn stt a c llo an tit oro nl s f .eature, is DASH SWITCH WIRE 143H **NOTE: The engine brake must provide a low engine speed S-32 SIGNAL RETURN shutoff feature, set to disable the brake at a speed slightly SEE NOTE ON INSTALLATION higher than idle rpm. DRAWING AS07-027 NOTE: If the engine brake solenoid is an inductive load, it must be diode suppressed. V07116 E2 BR O AKE N