Kaiyi — Kaiyi Power Train System Technical Manual

侍# Some fault codes are not applied to this machine. 3-70 Fault code (Hex) Meaning of the fault code possible reason for fault detection Reaction of the TCU Possible steps to repair B3 Slippage at clutch K3 TCU calculates a differential speed at closed clutch K3. If this calculated value is out of range, TCU interprets this as slipping clutch ÂLow pressure at clutch K3 ÂLow main pressure ÂWrong signal at internal speed sensor ÂWrong signal at output speed sensor ÂWrong size of the sensor gap ÂClutch is defective TCU shifts to neutral OP mode : Limp home If failure at another clutch is pending TCU shifts to neutral OP mode :

TCU shutdown 余 Check pressure at clutch K3 余 Check main pressure in the system 余 Check sensor gap at internal speed sensor 余 Check sensor gap at output speed sensor 余 Check signal at internal speed sensor 余 Check signal at output speed sensor Replace clutch B4 Slippage at clutch K4 TCU calculates a differential speed at closed clutch K4. If this calculated value is out of range, TCU interprets this as slipping clutch ÂLow pressure at clutch K4 ÂLow main pressure ÂWrong signal at internal speed sensor ÂWrong signal at turbine speed sensor ÂWrong size of the sensor gap ÂClutch is defective TCU shifts to neutral OP mode :

Limp home If failure at another clutch is pending TCU shifts to neutral OP mode : TCU shutdown 余 Check pressure at clutch K4 Check main pressure in the system 余 Check sensor gap at internal speed sensor 余 Check sensor gap at turbine speed sensor 余 Check signal at internal speed sensor 余 Check signal at turbine speed sensor Replace clutch B5 Slippage at clutch KV TCU calculates a differential speed at closed clutch KV.

If this calculated value is out of range, TCU interprets this as slipping clutch ÂLow pressure at clutch KV ÂLow main pressure ÂWrong signal at internal speed sensor ÂWrong signal at turbine speed sensor ÂWrong size of the sensor gap ÂClutch is defective TCU shifts to neutral OP mode : Limp home If failure at another clutch is pending TCU shifts to neutral OP mode :

TCU shutdown 余 Check pressure at clutch KV 余 Check main pressure in the system 余 Check sensor gap at internal speed sensor 余 Check sensor gap at turbine speed sensor 余 Check signal at internal speed sensor 余 Check signal at turbine speed sensor 余 Replace clutch B6 Slippage at clutch KR TCU calculates a differential speed at closed clutch KR. If this calculated value is out of range, TCU interprets this as slipping clutch ÂLow pressure at clutch KR ÂLow main pressure ÂWrong signal at internal speed sensor ÂWrong signal at turbine speed sensor ÂWrong size of the sensor gap ÂClutch is defective TCU shifts to neutral OP mode :

Limp home If failure at another clutch is pending TCU shifts to neutral OP mode : TCU shutdown 余 Check pressure at clutch KR Check main pressure in the system 余 Check sensor gap at internal speed sensor 余 Check sensor gap at turbine speed sensor 余 Check signal at internal speed sensor 余 Check signal at turbine speed sensor 余 Replace clutch B7 Overtemp sump TCU measured a temperature in the oil sump that is over the allowed threshold. No reaction OP mode : Normal 余 Cool down machine 余 Check oil level 余 Check temperature sensor B9 Overspend engine Retarder applies OP mode :

Normal - BA Differential pressure oil filter TCU measured a voltage at differential pressure switch out of the allowed range ÂOil filter is polluted ÂCable/connector is broken or cable/ connector is contacted to battery voltage or vehicle ground ÂDifferential pressure switch is defective No reaction OP mode : Normal 余 Check oil filter 余 Check wir ing from TCU to differential pressure switch 余 Check differential pressure switch(Measure resistance)