DISTRIBUTION SYSTEMS - LIGHTING SYSTEM Marker light Wiring harness - Testing (A.40.A.12.88 - G.40.A.20) AFX8010 9668 1 27/05/2004 A.40.A / 35 N° Test Point Expected Result Other Result (Possible Cause) 10 Turn Road Light Switch S-26 to High Beam position. Measure for 12 volts at High Beam Relay K-04 (pin 5). 12 volts If good reading, Go to test 11 Perform High Beam Relay Test. 11 Measure the voltage at RH Road Light E-14 connector X169 (pin C). 12 volts If good reading, Go to test 12 Open circuit 186 (PU) or 641 (PU) between High Beam Relay K-04 (pin 5) and RH Road Light E-14 connector X169 (pin C). 12 Disconnect the RH Road Light E-14.
Measure the resistance on circuit 643 (BK) between RH Road Light E-14 connector X169 (pin A) and ground. Less than 1 ohm. If good reading, replace the High beam bulb of the RH Road Light E-14. Open in circuit 643 (BK) between RH Road Light E-14 connector X169 (pin A) and ground. N° Test Point Expected Result Other Result (Possible Cause) 1 Turn Road Light Switch S-26 to Marker Lights position. Measure for 12 volts at Fuse #20. 12 volts If good reading, go to next test point. Perform Road Light Switch Test. 2 Measure for 12 volts at LH Front Hazard Lamp E-03 connector X357 (pin B). 12 volts If good reading, go to next test point.
Open circuit 624 (PU) between Fuse #20 and LH Front Hazard Lamp E-03 connector X357 (pin B). Short to ground on circuit 624 (PU) and 177 (PU) between Fuse #20 and LH Front Hazard Lamp E-03 connector X357 (pin B). Any short to ground will blow the Fuse #20. 3 Disconnect the LH Front Hazard Lamp E-03. Measure the resistance on circuit 620 (BK) between LH Front Hazard Lamp E-03 connector X357 (pin C) and ground. Less than 1 ohms. If good reading, replace the marker bulb of the LH Front Hazard Lamp E-03. Open in circuit 620 (BK) between LH Front Hazard Lamp E-03 connector X357 (pin C) and ground. 4 Turn Road Light Switch S-26 to Marker Lights position. Measure for 12 volts at Fuse #21.
12 volts If good reading, go to next test point. Perform Road Light Switch Test. 5 Measure for 12 volts at RH Front Hazard Lamp E-04 connector X356 (pin B). 12 volts If good reading, go to next test point. Open circuit 627 (PU) between Fuse #21 and RH Front Hazard Lamp E-04 connector X356 (pin B). Short to ground on circuit 627 (PU) and 176 (PU) between Fuse #21 and RH Front Hazard Lamp E-04 connector X356 (pin B). Any short to ground will blow the Fuse #21. 6 Disconnect the RH Front Hazard Lamp E-04. Measure the resistance on circuit 621 (BK) between RH Front Hazard Lamp E-04 connector X356 (pin C) and ground. Less than 1 ohms.
If good reading, replace the marker bulb of the RH Front Hazard Lamp E-04. Open in circuit 621 (BK) between RH Front Hazard Lamp E-04 connector X356 (pin C) and ground. 7 Turn Road Light Switch S-26 to Marker Lights position. Measure for 12 volts at Fuse #20. 12 volts If good reading, go to next test point. Perform Road Light Switch Test.