DISTRIBUTION SYSTEMS - LIGHTING SYSTEM 9668 1 27/05/2004 A.40.A / 36 N° Test Point Expected Result Other Result (Possible Cause) 8 Measure for 12 volts at LH Brake/Tail Lamp E-11 connector X299 (pin 3). 12 volts If good reading, go to next test point. Open circuit 412 (PU) between Fuse #20 and LH Brake/Tail Lamp E-11 connector X299 (pin 3). Short to ground in circuit 412 (PU), 625 (PU) and 177 (PU) between Fuse #20 and LH Brake/Tail Lamp E-11 connector X299 (pin 3). Any short to ground will blow the Fuse #20. 9 Disconnect the LH Brake/Tail Lamp E-11. Measure the resistance on circuit 634 (BK) between LH Brake/Tail Lamp E-11 connector X299 (pin 2) and ground. Less than 1 ohms.
If good reading, replace the marker bulb of the LH Brake/Tail Lamp E-11. Open circuit 634 (BK) between LH Brake/Tail Lamp E-11 connector X299 (pin 2) and ground. 10 Turn Road Light Switch S-26 to Marker Lights position. Measure for12 volts at Fuse #21. 12 volts If good reading, go to next test point. Perform Road Light Switch Test. 11 Measure for 12 volts at RH Brake/Tail Lamp E-12 connector X300 (pin 3). 12 volts If good reading, go to next test point. Open circuit 421 (PU) between Fuse #21 and RH Brake/Tail Lamp E-12 connector X300 (pin 3). Short to ground in circuit 421 (PU), 626 (PU) and 176 (PU) between Fuse #21 and RH Brake/Tail Lamp E-12 connector X300 (pin 3).
Any short to ground will blow the Fuse #21. 12 Disconnect the RH Brake/Tail Lamp E-12. Measure the resistance on circuit 635 (BK) between RH Brake/Tail Lamp E-12 connector X300 (pin 2) and ground. Less than 1 ohms. If good reading, replace the marker bulb of the RH Brake/Tail Lamp. Open in circuit 635 (BK) between RH Brake/Tail Lamp E-12 connector X300 (pin 2) and ground. 13 Place Road Light Switch S-26 in .ON. position. Measure for 12 volts at Road Light Switch S-26 connector X256 (pin 5). 12 volts If good reading, the wiring has good continuity, go to next test point.
Open circuit 213 (RD) between Road Light Switch S-26 connector X256 (pin 5) and Fuse #51 14 Remove the Light Control Relay K-02. Measure for 12 volts at (pin 5). 12 volts If good reading, the wiring has good continuity, go to next test point. Open in circuit 173 (RD) between Light Control Relay K-02 (pin 5) and Road Light Switch S-26 connector X256 (pin 1). A short will cause Fuse # 51 to blow. 15 Reinstall the Light Control Relay K-02. Measure for 12 volts at LH Marker Light Fuse #20. 12 volts If good reading, the wiring has good continuity, go to next test point. Open in circuit 121 (OR) between LH Marker Light Fuse #20 and Light Control Relay K-02 (pin 3).
A short will cause Fuse # 51 to blow. 16 Measure for 12 volts at RH License Plate Lamp E-57 connector X362 (pin 1) and LH License Plate Lamp E-58 connector X363 (pin 1). 12 volts If good reading, the wiring has good continuity, go to next test point. Open in circuit 177 (PU), 625 (PU) or 412 (PU) between Fuse #20 and RH License Plate Lamp E-57 connector X362 (pin 1) and LH License Plate Lamp E-58 connec- tor X363 (pin 1). Also Test backwards for 12 volts at circuits X005, X024, X071 and X243. A short will cause Fuse # 51 to blow.
17 Measure resistance at circuit 634 (BK) and 628 (BK) between RH License Plate Lamp E-57 connector X362 (pin 2) and LH License Plate Lamp E-58 connector X363 (pin 2) and ground. 0-2 OHMS If good reading, system OK. Open circuit 634 (BK) or 628 (BK) between RH License Plate Lamp E-57 connector X362 (pin 2) and LH License Plate Lamp E-58 connector X363 (pin 2) and ground.