DISTRIBUTION SYSTEMS - LIGHTING SYSTEM Front work light Relay - Testing (A.40.A.16.82 - G.40.A.20) AFX8010 9668 1 27/05/2004 A.40.A / 58 N° Test Point Expected Result Other Result (Possible Cause) 2 Close Work Light Switch. Use INFO Diagnostic Screen to check for voltage at CCM-1 (pin J1-3). 12 volts. If good reading, Go to test 3 Work Light Switch S-43. Short to ground on circuit 171(YE) between Work Light Switch S-43 connector X132 (pin 3) and CCM-1 (pin J1-3) A short will cause Fuse #49 to blow. 3 Measure for continuity at Work Light Switch S-43 connector X132 (pin 5) and Distance Work Light Relay K-21. 12 volts.
If good reading, Go to test 4 Open circuit 1 (OR) between Work Light Switch S-43 connector X132 (pin 5) and Distance Work Lights Relay K-21 (pin 5). 4 Measure for continuity at Work Light Switch S-43 connector X132 (pin 6) and Cab Roof Ground. Continuity to ground. If good reading, Work Light Switch S-43. Short to ground on circuit 61 (PU) between Work Light Switch S-43 connector X132 (pin 6) and Cab Inner Work Lights E-15 and E-17 connector X115 and X117 (pin A). N° Test Point Expected Result Other Result (Possible Cause) 1 Place Key Switch S-02 in ON position. Close Work Light Switch S-43. Measure for 12 volts at Lower Work Lights Relay K-30 (pin 5). 12 volts.
If good reading, the relay is operating properly. Lower Work Lights Relay. Adjacent circuits. Go to test 2 2 Measure for 12 volts at Lower Work Lights Relay K-30 (pin 1). 12 volts Go to test 3 Open or short to ground in circuit 187 (WH), 188 (WH), 189 (WH) or 190 (WH) between Lower Work Lights Relay K-30 (pin 1) and CCM-1 (J1-11). See Service Manual for testing of CCM. 3 Measure for 12 volts at Lower Work Lights Relay K-30 (pin 3). 12 volts If good reading, Go to test 4 Open in circuit 64 (RD) between Lower Work Lights Relay K-30 (pin 3) and Fuse #54.
Short to ground in circuit 65 (PU), 645 (PU), 644 (PU) or 646 (PU) between Lower Work Lights Relay K-30 (pin 3) and Lower Work Lights E-23 and E-24 or Grain Tank Light E-30. A short will cause the Fuse #54 to blow. 4 Disconnect the Lower Work Lights Relay K-30. Measure resistance on circuit 157 (BK) to Lower Work Lights Relay K-30 (pin 2) and ground. Less than 1 ohms .1 ohms _ If good reading, replace Lower Work Lights Relay K-30. Open in circuit 157 (BK) to Lower Work Lights Relay K-30 (pin 2) and ground. 5 Place Key Switch S-02 in ON position. Close Work Light Switch S-43. Measure for 12 volts at Header Work Lights Relay (pin 5). 12 volts. If good reading, the relay is operating properly.
Header Work Lights Relay Test. Adjacent circuits. Go to test 6 6 Measure for 12 volts at Header Work Lights Relay K-22 (pin 1). 12 volts If good reading, Go to test 7 Open or short on circuit 188 (PU), 189 (PU) or 190 (PU) between Header Work Lights Relay K-22 (pin 1) and CCM-1 (pin J1-11). See Service Manual for testing of CCM.